Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
I have a Thingy:91x.
I flashed a BLE central program to the nRF5340 on this device.
However, I get an error initializing BLE. I've confirmed that this program...
Board/Setup:
Board: nRF9151 DK / nRF9151 SoC
Peripheral: External BLE module connected via UART1
Use case: BLE module is only needed during commissioning...
Hi there,
I have been trying to implement a low-power mode that basically suspends UART, I2C, etc before entering sys_poweroff() when critical battery level is triggered...
Hi,
I have several field devices using the LTE Link Controller library with nRF Connect SDK v2.5.1. Most of them work fine — they are programed to connect every hour. However...
Greeting Nordic Expert !
I would like to override the following hook in MCUboot:
int boot_perform_update_hook(int img_index, struct image_header *img_head, const struct...
Hello,
In the nRF52840 Product Specification PDF v1.11, on page 836, the second paragraph down states:
" The PSEL.RXD, PSEL.CTS, PSEL.RTS, and PSEL.TXD registers and...
Hello Nordic team,
I’m using the nPM1300 development board to charge a 950 mAh Li-ion battery , and I’ve configured the charger as follows:
Charge current: 800 mA...
Hi,
I'm unable to get the PPKII kit to "connect" to my PC. After selecting the device it just says "Connecting..." forever. Some notes: - When first connecting the kit...
Hello,
I am trying to write a python script that performs a DFU on a nRF52840 so I can change its firmware without pressing any button. I think I have to use the pyusb...
Hello everyone,
I’m currently planning to develop an application that involves multiple Bluetooth devices operating within a certain range outdoors. Since there’s no option...
I’m developing an ESB-TX program using NCS v3.1.1 . Previously, I had developed an ESB-RX program using nRF SDK 17.0.2 . Now, when I use the TX code from the NCS SDK to communicate...
Hi,
I'm new to embedded development but have experience in desktop C/C++ development mostly with Visual Studio.
I'm struggling to get my head around how I would create...
Hello,
I am trying to define a pm_static.yml file which will use the 512K ram on the nrf7002dk_nrf5340 for the TFM ram section.
I cannot compile the non-secure nrf7002dk...
Hi, I got my nrf54L15 DK, but i can't start RTT logging. I set this configs:
CONFIG_PRINTK =y
CONFIG_CONSOLE =y
CONFIG_RTT_CONSOLE =y
CONFIG_UART_CONSOLE =n
CONFIG_USE_SEGGER_RTT...
