Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
What is the permitted VDD ripple on the nRF9151?
I see " To minimize supply voltage ripple and suppress EMI coupling to and from nRF9151 VDD , keep supply network impedance...
Hardware Setup
Custom Board:
nRF52811 chip
No external LFXO (32.768 kHz crystal)
No LC filter for DC-DC regulator
No peripherals connected (no LEDs, buttons, sensors...
Hi,
I try to use the west ncs-sbom command to generate the result, however i meet below error happening but I had not idea how to solve it could someone help me to check...
The issue is that , i have custom board which have nrf52833 and nrf21540 (Range extender) , i have to increase the range of tx gain = 20dbm using gpio method
this is my...
Hello,
I have developed a bootloader with OTA update functionality on an nRF device. The partition switching code (bootloader jumping to the application after OTA) works...
I am running into a recurring issue with attempting to connect to a nRF52840DK advertising using extended advertising from iOS devices. Connections repeatedly fail to establish...
I am not using the nrf5340DK development board; instead, I am using the nrf5340 chip, and the SDK version I'm using is V3.1.0. I defined the I2C child node "lt3582" in the...
I set CONFIG_BT_DEVICE_NAME_DYNAMIC=y in prj.conf, and then called it after the system started.
These functions modify the Bluetooth name, but the new Bluetooth name has...
