Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi Team,
I am using NCS v2.9.0 and trying to implement a custom Zigbee cluster with custom attributes.
Could you please suggest an example or guide me on how to send...
I'm currently testing the walkie-talkie mode on this development kit, however, when testing it outdoors it only allows a very short connection distance and disconnects. How...
Hi, this question might sound a little silly, but is downloading my device location history from nRF Cloud free of charges? I want to analyze my device's travelling pattern...
Hi there,
I am using an nRF9160DK and looking to get accurate Timing Advance numbers from it and also information on neighbouring cells. I believe in order to get an accurate...
We are using both serial ports running over USB on the nRF54L15DK:
uart20 is LOG, CONSOLE, etc.
uart30 is for our communication (enabled in our overlay)
When we...
Hello,
I am trying to get a custom board working with NOR Flash chip but I am having issues getting the flash chip "ready". I am running the sample application "spi-flash...
Hi!
I've used nrfutil to dfu ble before on a target that just loads and runs a bootloader (for cycle testing).
I'm trying to use it again with a target in the application...
We have a NCS 3.0.2 app + MCU boot with OTA functionality on nRF54L15 (PCA10156 rev 0.9.3)
After upgrading to NCS 3.1.1 it doesn't boot anymore.
I tried with
Key provisioning...
nRF9151 has access port protection enabled by default. I need to debug firmware for nRF9151 produced by a non-secure build. I am trying to follow Figure 120 (Access port unlocking...
Hello,
I have a series of nRF52840 devices that are already connected together in a Thread Network.
My system is composed by one client and multiple servers.
My devices...
Is there any way to filter for verified answers/closed tickets? Seems like it would be really useful for helping people find answers and answer posts which have none.
Greetings,
Using SDK v3.1.1 I've configured 3 PWM outputs using the pwm0-2 modules via a DTS overlay. After reset or power cycle (and prior to making any PWM driver calls...
After cancelling a flash operation to my nrf7002DK (PCA10143 1.0.2), I'm unable to flash my discovery kit again. I have tried both the regular west flash for our application...
Hi,
I use flash read operations at the BLE interrupts, because I need some of the stored informations. However, while I am doing another flash operations and BLE interrupt...
Greetings,
What's the maximum clock rate supported by the SPI1 interface on an nRF52840? My DTS overlay indicates it should use 32MHZ for one device and 8MHz for the other...
