after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi Nordic
I am working with nrf52840 and nrf52832 using ncs v2.8.0
I am trying to save coredump to flash according to instructions on this link - https://docs.nordicsemi...
Hi everyone,
I'm working with the nRF52840 using the nRF5 SDK v17.1.0 and SoftDevice S140 v7.2.0 . My application uses QSPI for external Flash communication.
I have some...
Hi,
i just noticed that for the nRF5340DK board, the file nrf5340_cpunet_reset.c has been removed.
Nevetheless it is still reference in the documentation online: https...
Hello,
We have built a device that uses the nRF52840 reference design shown below. With the configuration shown the board advertises as expected. If we replace either...
Hi, I try to use the example Bluethoot LE Wi-Fi provision in the nRF7002 DK and in the step to see the Wi-Fi Networks in the APP appers internal error.
Development kit...
Hi,
I'm developing a custom window cover device for Matter and I have a weird issue where Matter packets sometimes seem to take a very long time to go though. Window Cover...
Hi, It would have been quite useful if nRF54L15DK had CR2032 battery holder to carry around for experiments. since this board does not have it any recommendation to conne4ct...
I used the device tree to assist with schematic design, but after the PCBA was returned, I found that the peripheral functions could not be implemented normally.
It was...
NCS3.1.1, Windows10, VScode, NRF52840 custom board
With 3.1.1 I've discovered the paths in the "Edit build configuration" wizard are being broken and silently ignored during...
Hello DevZone,
May I know if there are any hardware SoCs and development kits that operate in Wi-Fi Halow(802.11ah) standard? Please point me out if there are. Thank You...
Hi,
I tested uart30 of NCS3.1.1, and found that I could not enter the low power consumption mode.But there is nothing wrong with uart20.
Related code usage:
prj.conf...
Hi,
I have a nRF5340 DK (PCA10095) that was working fine on the nRF Connect v4.2.1. I use the Direct Test Mode functionality.
However, after updating to v5.2.0, the DTM...
Hello, I’ve been exploring DECT NR+ on the nRF9151-DK using the DECT modem firmware. As it was already mentioned in multiple threads/other sources, there is no GNSS or LTE...
Hi,
I need support to get my brand new nrf9151 development board LTE connection up and running.
I have bought this kit and it came with 2 SIM cards as per documentation...
