Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
I'm using SDK v3.0.2, and I'm having some confusion when using this tool.
For example, I want to enable Bluetooth Broadcast Sink Audio Support, but I can't click on it....
Hello,
I would like to use NFC on my Thingy:53 to send data or at least a word, how do I set it up? I haven't found any code anywhere.
Thank you in advance
Kind regards...
Hello,
We have been using a custom device based on the NRF9160 SIP with a HTTPs connection for tracking animals and are planning on makeing changes to CoAPs and upgradeing...
Hi Nordic Team,
I have developed a custom board using the nRF9151 controller. I am testing the GNSS sample from nRF Connect SDK v3.0.0 . When I flash and run the firmware...
I have a PPK2 on hand.
Here is what happened:
1. When I first connected it to my Windows 11 PC, the Power Profiler app in nRF Connect for Desktop detected the device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi.
Developing PAwR in project, I have some Question.
before Asking, My Project Structure is below.
1 Gateway (Advertiser) - Node1 (Scanner)
- Node2 (Scanner)
-...
Hello,
I'd like to send/receive data over UART using the expansion board connector of my Thingy:91 X (pins 0.18 & 0.19 as RX/TX). With SB8&9 separated (to isolate pins...
Hi,
I was able to purchase a commercially available 30cm ribbon cable to connect from the nRF54L15 DK to a custom board for programming. I later realized the DK documentation...
Hello,
I have custom hardware using an nPM1300 and nRF52840, and I am having trouble getting the nPM1300 to work as described in its documentation. I have a button connected...
I am trying to write a low level driver for the TWIM system in a nrf52840 and cannot seem to get the hardware to transfer the TX data out of memory. For many reasons, I do...
I am working on project with nrf54l15dk/nrf54l15, and the project runs on cpuapp without utilizing flpr. So, I decided to release the allocated section of flpr on rram_controller...
I'm seeing an issue where nrf91 SLM, running as an AT modem over UART, sometimes chokes on XSEND command and doesn't respond until the host (nrf54) sends another AT command...
i got the following code from here: https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/zephyr/kernel/services/timing/timers.html , and am using version 3.1.1 of the SDK
...
Hello, I am currently trying to use kmu to store a series of derived keys. My current systems derives AES keys and attempts to store it into KMU. As psa_key_derivation_output_key...
