The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
Hello everyone,
I'm working with the nRF5340 and I would like to connect a LIS2MDL sensor(see the schematic below).
The sensor has two power pins: VDD and VDD_IO . Initially...
I've been living with this for a while now, but it's getting annoying very quickly. I have a project in VS Code that uses the nRF Connect extension to build for nRF52832 and...
Hi
I want to use the FEM 21540 with nRF54LM20.
My overlay is :
My config is:
I think this should work because my nRF54L15 DK works well with this.
But it is...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
Hello. I used the "peripheral_nus" example for nrf52840 - everything goes as it should - I connect via bluetooth and the "nrfConnect - mobile" application receives the message...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
I am currently re-qualifying our Bluetooth product in Bluetooth SIG Launch Studio because we had to migrate from NCS SDK 2.1.4 to 2.9.2 due to a security...
Hello, I know this is not the best place for this question, but I did not find any other way. How can I delete my profile from your website including all related data?
Kind...
nRF54LM20A:
C pin is the pin input capacitance on pins XC1 and XC2 .
Could you provide the typical, maximum, and minimum values of Cpin?
This information is needed...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello. I am a beginner and I have a nrf52840 Dongle board. I tried to use the interrupt from TIMER0. I defined the timer and it works correctly, but when I enable the interrupt...
