The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Are there any up to date samples for running BLE on nRF9160 development kit? I've tried building the following sample: https://github.com/nRFCloud/lte-gateway/tree/main for...
Hewy there:
I have a custom nRF52833 board with NCS v3.1.0, using ESB and USB CDC ACM. The external 32 MHz crystal is oscillating fine — we see a clean 32 MHz sine wave...
Hello!
I am having problems reading the SIPINFO on the SoC. I started with the TFM sample and added some lines to read the silicon version. added lines:
printk ...
Hi Nordic Team,
I have been working on the Bluetooth Channel Sounding (CS) Initiator and Reflector samples using nRF Connect SDK v3.3.0 on nRF54LM20B devices , and I was...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
When implementing a custom service, the order is usually Generic Access, Generic Attribute, and then the custom service.
Is it possible to change this order to custom services...
I want to develop for the nRF5340 on the Thingy91X. Are there any good sample projects that allow me to set the target board to Thingy91X/nRF5340/cpuapp?
I only need to...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
i2c_write_read() returns -5 (EIO) immediately when writing register 0x01 to the sensor. Logic analyzer confirms the sensor clock-stretches SCL for ~14µs+ after receiving the...
Hi All,
We have trying the usbd_cdc_acm example program.
It has custom VID and PID. When connected to a windows PC with the correct driver, it is recognised correctly...
Does SDK 3.3 support building hci-lpuart for the Thingy91x yet? I would love to change to that device if it does.
If it does not, are there plans to implement it?
Hi,
I'm running into what looks like a software link-layer issue on the nRF54L15-DK that I'd like a second pair of eyes on. The same firmware works end-to-end with iOS...
Hi,
I’m using GD25WB256 as external flash on nRF9151 for MCUboot secondary slot. It’s currently not available from our supplier, so I’m looking for alternatives.
Current...
Hi everyone,
I am currently facing an issue with the nRF54LM20A where the access port protection is not taking effect after programming SECUREAPPROTECT and APPROTECT into...
