hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi, I am unable to read GPIOs (always getting 0x00000000 from gpio_port_get or 0 from gpio_pin_get). My main project is https://github.com/marcuswu/leaf-fall/tree/main/firmware...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
Hello everyone,
I'm working with the nRF5340 and I would like to connect a LIS2MDL sensor(see the schematic below).
The sensor has two power pins: VDD and VDD_IO . Initially...
I've been living with this for a while now, but it's getting annoying very quickly. I have a project in VS Code that uses the nRF Connect extension to build for nRF52832 and...
Hi
I want to use the FEM 21540 with nRF54LM20.
My overlay is :
My config is:
I think this should work because my nRF54L15 DK works well with this.
But it is...
Hello everyone,
I’m currently porting my old projects from NCS version 2.9.0 to 3.3.0.
In doing so, I no longer want to use the outdated Partition Manager; instead, I...
Hello. I used the "peripheral_nus" example for nrf52840 - everything goes as it should - I connect via bluetooth and the "nrfConnect - mobile" application receives the message...
Hi Team,
I am working on an nRF52811-based BLE application using nRF Connect SDK (Zephyr) and facing an issue while trying to store the device name in flash using the Settings...
Hello Nordic Support,
I am currently re-qualifying our Bluetooth product in Bluetooth SIG Launch Studio because we had to migrate from NCS SDK 2.1.4 to 2.9.2 due to a security...
Hello, I know this is not the best place for this question, but I did not find any other way. How can I delete my profile from your website including all related data?
Kind...
nRF54LM20A:
C pin is the pin input capacitance on pins XC1 and XC2 .
Could you provide the typical, maximum, and minimum values of Cpin?
This information is needed...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
