Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hi, I'm experiencing a significant performance drop when switching from the nRF9160 to the nRF9151DK.
I have a firmware that sends around 300 kBytes of data over UART in...
Hi, I recently upgraded my nRF Connect SDK to 3.1, and have migrated my code (which was originally based on the direction finding connectionless example) to 3.1 so that it...
Our Jenksing builds when using Nrf Connect v2.7.0, the --no-sysbuild option and CMakePresets worked just fine. When migrating to Nrf Connect v3.0.2 and using sysbuild, they...
I have some issues with the default response handling.
My Zigbee door sensor sends a message, and I reply with the following code:
```
if ( ! cmd_info -> disable_default_response...
I need to maintain and update firmware written with 15.3 SDK on an nRF52832 on Windows 11. What is the exact software and tools I need to do this. The latest Segger development...
Hello,
My use case is the exact same use case as this forum post . I'd like to run BLE and Radio Test sample on the nRF5340. The device would be in 2 modes:
- BLE
-...
Hello,
I try to figure out, how to correctly setup MCUboot for an nrf5340, so that:
Application is updatable
BT Stack is updatable
Firmware Updates are encrypted...
I am trying to enable a watchdog and then stop it. i closely followed the datasheet way to do this. the problem is that the watchdog once enabled will always fire. i want...
I'm working on nRF5340 custom platform (NCS 2.6.1, Zephyr 3.5.99). I use MCUBoot immutable bootloader and external QSPI NOR Flash for slot-1 partition during DFU.
This is...
Hi Nordic Team,
I am working on the Matter Smoke/CO Alarm example with ICD (Intermittently Connected Device) support enabled.
My operational mode is working correctly...
I'm trying to replace HM-10 module with a RAYTAC MDBT42TV-DB-05 for a transparent UART (serial passthrough) application. I've configured all the parameters and GATT settings...
in fact , I have the while sdk directorys. in c:/ncs/v3.1.0 but,the nrf extension in vscode cannot recognize it. it always info me to install a sdk in welcome page. so, I...
I am using nRF52840, we have an issue which seems like a standard issue with nordic switching between regular battery and a coin cell backup.
I need to know the following...
Hi Support Team
Is the ifft the measured distance? I test the channel sounding sample in NCS v3.0.0 and find that the ifft distance error is relatively large. How to optimize...
My new PC could not find PPK in the power profile menu, even I installed different version nRF connect desktop or different Power Profile versions. I always could not find...
