Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I tried to build the Blinky sample description in nrf sdk fundamental academy training without success.
Error occur during build at B0n stage:
error: 'struct shell_ctx...
## Summary Setting `CONFIG_MEMFAULT_NCS_INTERNAL_FLASH_BACKED_COREDUMP=y` on an nRF54L15 target fails to compile. The Kconfig is exposed (it only `depends on PARTITION_MANAGER_ENABLED...
Hello, one of our devices moved from using the nRF52832 to using the nRF54L15 .
I created new board files and got the old software to run, after some adjustments. The application...
Hi everyone,
I’m working with a Zephyr input overlay where I define double-tap , longpress , and extra_longpress behaviors on the same physical button.
This is the overlay...
I am updating my ncs from ncs2.7.0 to 2.9.2. I have a dfu application for which the build targer is nrf52840 and nrf5340. For this reason, I have pm_static files. for some...
I am using SDK version v3.2.1 and trying to put the nRF54L15 DK board into deep sleep using the sys_poweroff () function and wake it up using Button 1 on the DK.
This setup...
I get this error when i try to use FATFS or LittleFS - RAM works though /Users/admin/mass_1/src/main.c: In function 'setup_flash': /opt/nordic/ncs/v2.9.0/nrf/include/flash_map_pm...
Looks like Gazell can't run on nrf52810 with nrf5 SDK :
I don't knnow whether it is possible to create app on it with nrf connect SDK.
I think nrf connect SDK will need...
Hi, I have purchase a circuitdojo_feather_nrf9151 board it has LIS2DH12 and npm1300 on i2c2 i also want to connect SHT40 but facing issue this sensor is not detecting on i2c...
Hey all, I wanted to enable shutdown and standby modes for this chip, but realised that I can not use the layer of zephyr. When i try to CONFIG_PM=y in prj.conf it does not...
Hi,
I'm running the system_off/ sample on v3.2.3 with these settings in prj.conf
And with this overlay file:
However, I can see that there's a high (and in fact...
Hello, I'm building a multi-image project for an nRF9151: a two-stage bootloader (NSIB + MCUboot) plus two independent non-secure app images.
Each app needs to be able to...
I'm trying to capture a ble connection with nrfutil. What I've done:
- installed nrfutil on my arch based linux machine
- install ble-sniffer
- setup the nRF52840 Dongle...
I am aware from this post https://devzone.nordicsemi.com/f/nordic-q-a/106424/ble-audio-test-app-supporting-both-cis-and-bis t hat the primary LE Audio controller does not...
