here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hello Team,
We have noticed a very weird issue with the nRF5340 Audio DK. After flashing the audio application code given by nordic, everything works perfectly fine. No...
I have asked if I can post this request, ticket number 354361.
Can you help with new research on secure boot?
I am a cyber security researcher at the University of Bristol...
Hi there
I have a question about the way the nRF52 radio handles on air addresses. I currently am developing custom software that uses the nRF52810 radio for a custom protocol...
I’m working with a Manufacturer-Specific Cluster (Attributes) in the Matter Template sample from NCS SDK v3.1.1, and it works fine with attributes. However, when I try to...
Hi, We designed a board using NRF5340-CLAA-R by following the Altium Reference design. Although when we tried to place an order with JLCPCB or PCBWAY, then informed that they...
Hi, I am pretty certain I have used RTTViewer before on the nRF9160, albeit not frequently. I cannot remember if I only used it on custom nRF9160 boards or if I used it on...
hello,
on our bm833 dev board, I scope (using a PIO) the time it takes for the bt_nus_send function to send 146 BYTES. The PIO goes to 0 after the callback nus_sent_cb has...
Summary
We are developing a Central application on the nRF7002 DK (nRF5340 SoC) using NCS v2.7.0 . The goal is to establish and maintain 11 concurrent Bluetooth Low Energy...
We're working on a project that interfaces an nRF9151 with a BQ40Z50 from Texas Instruments (via I²C / TWI / SMBus), and we've noticed the communication is unreliable. The...
Hi,
We are currently working on power optimization and want the device to wake up from the System ON state ( PM_STATE_SUSPEND_TO_IDLE ) using the RTC0 timer. However, I...
Trying to prototype a pinout on the nRF54L15 dev kit. We want P1.02 to be a GPIO pin instead of NFC. We followed the instructions to recover the device which erases the UICR...
Hi,
I am facing the following issue when i am calling west build from gitlab runner.
west: unknown command "build"; workspace C:\ncs\v2.5.0 does not define this extension...
Hi,
I am trying to come up with a different approach to SED reattachment using a backing off MLE session. Is there a way for the SED to keep on the polling even when in...
I'm working on an nRF9151 application that periodically sends small UDP packets (20-40 bytes) over both terrestrial LTE and satellite NTN networks. The device uses PSM between...
