Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello!
I have stored a PSK in the KMU of my nRF54L15, and now want to use it for a Lwm2m client DTLS connection.
According to Zephyr's documentation, the PSK must be provided...
Hi, I'm using v2.7 toolchain and v2.61 sdk, I tried with both wifi sta and wifi shell example, both failed to build when CONFIG_WPA_SUPP=y, if I comment out this config, then...
I have succesfully tested my software that sends gnss location to aws iot with nrf9151dk. Recently I configured software also support also thingy91x. My problem is that Aws...
I've nrf52833dk board, I'm doing i2c exercise from Dev Academy's NRF connect sdk fundamental course. For some reason I used 'Quick Start' option in "nrf connect for Desktop...
Dear Nordic teams :
I would like to clarify the capacitor usage configuration:
1. If the firmware is configured to use the internal load capacitor and I also place external...
Hello,
I'm building a project on a Xiao nRF52840 Plus board. When I built and flashed the firmware, the Nordic LED Button Service does not appear in the nRFConnect app....
I have a custom board with bl54u and NPM1300 . Working fine.
But now replaced with a NPM1304 as it is pin compatible. Worked fine with fuel gauge NPM1300 on SDK 3.0.1. ...
We've derived a DTLS handshake test firmware from github.com/.../l5_e2_sol
Tests have been done using nRF9151 DK, SDK 3.1.0 and modem firmware 2.0.2.
First we verified...
I'm putting together a project that requires a "large" (1500mAh+) rechargable battery, both because of the desire for long times between charges and to enable powering a peripheral...
Hello Nordic Support Team,
I'm working with the Android-nRF-Wi-Fi-Provisioner library ( https://github.com/NordicSemiconductor/Android-nRF-Wi-Fi-Provisioner ) and would...
I'm using the Nordic nRF52840-DK. I'm having a hard time with logging using RTT. Sometimes it works, sometimes it does not. Usually I get a few runs where it works, then it...
I developed a custom application on the 52840DK and have now moved this over to a custom PCB of my own design. I can compile OK and can start a debug session from "main" but...
I am unable to download the nrfjprog command line tools from your website.
I am using SDKV1.8.0 and Toolchchain V2.0.0. in Visual Studio Code.
When I attempt to flash...
Hi,
I have low power environmental sensor. They raise an interrupt that something was sensed and require to read some registers on the sensor via I2C and run a state machine...
Currently, the nRF Connect extensions are available only on the Visual Studio Code Marketplace. We primarily use Cursor, which is a VS Code fork designed for enhanced AI-assisted...
