We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello,
I am solving a problem with nRF7002-DK, I am using TCP sockets for communication. MTU can have up to 6800 bytes, unfortunately, both in STA and AP mode, the connection...
My prj.conf:
First question / issue:
I am trying to make use of the azure dps and since I'd like to use the UUID as device id i am trying to set 'AZURE_IOT_HUB_SAMPLE_DEVICE_ID_USE_HW_ID...
I am trying to make an ndef record using t4t, but it fails.
For example I'm trying to convert the example 'record_text' to work with t4t setup, and it always fail.
Is...
Setup: nrf5340dk Zephyr: ncs 3.1.0 Hi, I am trying to enable firmware update for CPUNET over Serial (USB_CDC). I enabled update for CPUAPP and it works correctly, but not...
Hello,
I am working on a custom board based on the nRF5340 SoC . When I build any BLE sample (for example, peripheral_hr or peripheral_uart ) for the nRF5340DK , the build...
Hi, the nrf54l15 DK documentation states "nRF Connect for Desktop's Board Configurator application can be used to select if the nRF54L15 SoC interfaces with the external memory...
Hi,
I am using NC9 2.9.0 with VSCode and NRF extension.
I have seen that since version 1.2 of Device Information Service (DIS) spec , it is theorically possible to have...
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
I have a custom board with a nrf5340. I flashed two of them with two different names and opened up the nrf Connect app on iOS. I was expecting to see them side by side but...
Hello Nordic support,
My application is a Zigbee coordinator application on nrf52840 based on nRF5 SDK for Thread and Zigbee v4.2.0. I was able to pair a Zigbee end device...
I have successfully implemented an I2C interface example for AS5600 chip now I want to redirect the printk logs to UART over USB. For some reason I'm not able to make the...
" The ultra-low latency (ULL) Human Interface Device (HID) enhancement project aims to make Bluetooth gaming controllers as responsive as those using USB-wired or proprietary...
Hi,
My development environment:
- VS Code
- nRF Connect SDK: v2.7.0
Description:
- My firmware had successfully paired (with passcode) with an iPhone. Security level...
Hi everyone. When configuring the GATT role, there are GATT server role, GATT client role and both. When using nRF5 SDK or nRF Connect SDK Bare Metal, is it possible to configure...
Hi there!
I'm working through the nrf_cloud_multi_service sample, and have a few questions.
Here is my setup:
nRF9151DK
nRF Connect SDK v2.9.0 and corresponding...
