I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
1. can you tell in detail about Easy DMA supporting on SPI, I would like to understand how I can utilize DMA feature for communication with RAM over SPI what is the added...
Hi
We have nPM1300 evaluation kit, we use SW1 VOUT1 1.8V as VINLDO1 input, we remove jumper JP7(for LS_LDO_OUT1 connect to R8) on P15 connector, and provide 1kohm loading...
We just started a project to replace an old PAN1720 and decided to use the nRF54L15 based module. So I am just getting started with the VS code and zephry enviroment using...
The UART (Port 2) gets garbled after bt_enable(). This issue does not occur if actively Debugging using Segger.
The issue is also reproducible upon a settings_save_one(...
Hi,
I am using nRF54L15, SDK & Toolchain as 3.0.2 version This is for Hid Keyboard, the problem I'm facing is once connected to one device, manually disconnecting & connecting...
Hello,
There are some issues I have found when I tried to achieve both BLE and ESB features concurrently on nRF54L chips, and some of them I have figured out how to fix...
I have BOARD_ROOT set in both zephyr/module.yml and in CMakeLists, and in my boards folder I have a custom board "boards/nordic/myboard". I have all the necessary files for...
Hi Nordic team,
I’m building an LE Audio gateway on the nRF5340 DK using the TMAP_Central sample (NCS v3.0.2, with minor local changes). The setup captures audio, encodes...
I'm working with nRF52840 microcontroller, nRF SDK 17.1.0 and Softdevice S140 version 7.2.0
The peripheral devices sends 29 bytes of data with a BLE notification from a...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
I'm currently using firmware advertising/scanning with 1M PHY, but I'd like to use Coded PHY instead. I tried changing the advertising parameters as shown below, based on...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
I have LIS2DW12 (Gravity board) connected to my NRF54L15-DK with the following overlay:
& pinctrl {
/* Pin control for I2C21 */
i2c21_default: i2c21_default...
Hello,
I have set up the light and light_switch BT Mesh examples on my nRF52840DKs. I have used the nRF Mesh app to provision them successfully and I can see that they work...
Hi,
I am using NRF Connect environment and would like to enable by program to use MCU Boot functionality with dual-imaging support and FOTA updates.
My Kconfig.sysbuild...
