I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
Hi ,
I’m working on an nRF5340 using nRF Connect SDK v2.7.99-cs2 . BLE security is configured as Just Works (Security Mode 1, Level 2) on the peripheral .
I’m attempting...
I am using the nRF54L10 on a custom board with a couple of LEDs, a flash storage device and a GNSS device. The application wakes periodically to gather fix information from...
How can I detect when no SIM card is inserted at startup? The purpose is to operate without a connection if there is no SIM card.
[Environ] nRF Connect SDK v3.2.1 nRF9151...
Hello,
I was learning about how the bt_conn references work, how to obtain them and free them, and where they are generated.
I was looking at the central_gatt_write...
Hi
I have currently claimed devices in my nRFCloud I registered two years ago. It looks like this:
It has the mention "powered by memfault" . This is also the nRFCloud...
Hi,
i'm learning l4/e1 and i'm trying to buid the process after finishing step 10 but the build didn't goes through successfully. i got this errors
my SDK & toolchain...
Hello all,
I have an nrf54l15 on a custom board, I am having issues getting a reliable SPI clock signal when using BLE advertisements
This is the clock and correct...
I bought both nrf52 DK with nrf52832 and ISC-nRF52810-A module. I use Visual Studio Code with nrf SDK + toolchain. Hardware connection from ISC-nRF52810-A to nrf52 DK is as...
The openthread coprocessor sample in sdk v2.8.0 and v3.1.0 work for me with the openthread border router but not the sample in sdk v3.2.1
I followed the instructions for...
Hi,
i'm learning the exercise1 for AT commands to control modem and when i apply this command AT%XMONITOR i get the output as %XMONITOR: 5,"","","24202","0901",7,20,"02024720...
nRF52810 program execution failed the CPUID verification. Hi everyone, I have a question. I have a working PCBA with an nRF52810 as the main controller. When reading the CPUID...
