I am toggling Value of slave through a button on nrf51822ek .This Value is displayed on MCP of dongle, but i have to get this value on terminal to send it to pi then through...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello! I have 126 kB MCUboot partition which I'd like to make immutable (write protected so it can't be corrupted). I have serial-recovery, KMU key handling, debug optimization...
When building applications/hpf/gpio with -DSB_CONFIG_HPF_GPIO_BACKEND_ICMSG=y on nRF54L15 DK (NCS v3.2.4), the build fails with error: '__device_dts_ord_DT_N_NODELABEL_ipc0_ORD...
Dear DevZone Team
To detect possible TWI slave devices connected on a TWI bus, we want to scan for device addresses and check if they are being acknowledged.
In the twi_scanner...
When a BTLE Connection is underway, calling bt_disable can result in an infinite hang in the Zephyr BTLE stack. Using ncs v3.0.0 Any ideas? There is some mention of: CONFIG_BT_HCI_ACL_FLOW_CONTROL...
I have implemented the erase protect and app protect in our application. There are commands for locking and unlocking the device. Actually, during testing I was able to lock...
Hello Team,
I am working with Thingy: 91x and I have searched your websites for Schematic for some understanding purpose used in Thingy: 91x Kit.
But I couldnt find any...
Hello, I started working with the nRF Cloud and have been trying to understand the authentication procedure. From my understanding, the create_credentials script creates the...
Greetings, my name is Toni. We are trying sending the MO PS SMS-over-CP/NAS or IMS from the nRF9160-DK: - Hw rev2, - mfw v1.3.7, - NCS prebuilt apps from the v2.3.0 and v3...
Hi Nordic team,
I am designing a new board from scratch around the nRF52832 in KiCad.
My current plan is to use the nRF52832-QFAA/QFAB QFN48 package on a 2-layer PCB....
Hi,
Using the Matter template sample, I'm not able do to the commisionning until the end because I got an error saying " an error occured" on my border router( using an...
We are currently developing a nrf52840 firmware which should support RSCP as collector.
Setup:
nrf52840
ncs2.9 with
Q322804 NCS Host
Q331587 SoftDevice Controller...
Hello,
I have been trying to find an answer to this in the documentation but have thusfar been unsuccesful. For our use case we use the Certificate management part of the...
After Can the ESB protocol be added to the nrf desktop routine? . I tested the code for switching from ESB to BT (Non-Concurrent)。
The SDK version I used is V3.2.0. The...
Hi,
I'm looking for any help to implement wifi OTA for nrf54l15, found a lot of docs about FOTA for upload firmware over ble but i need to upload the firmware located at...
I am working with the nRF9151 (SMA) and attempting to place the system into the lowest power state using sys_poweroff() .
After entering this state, I observe undefined...
