Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi All
I have a question here.gatt Characteristic uuid has been Modified After the equipment has been in run for some time.
Current conditions of the equipment:
1.The...
Hi all,
I'm trying to use SPI Slave on a proprietary Hardware that use Ezurio BL54L15 (that contain a Nordic nRF54L15 chip). The environment is VSC + nRF Connect SDK 3.1...
Hello Nordic team,
I’m using the Mikroe nPM1300 PMIC Click Board (based on the Nordic nPM1300 PMIC ) with an ESP32 over I²C to charge a Li-ion battery.
Setup details:...
Hi,
May I know if the ncs add-on sdk-ant also supported nRF52833 because it is not mentioned in the list. Thanks.
Compatibility — ANT for nRF Connect SDK documentation...
Hi,
I need to use GRTC channel 0 in a nRF54L15 project. Channel 0 is special. It is the channel that the INTERVAL register controls. `zephyr/boards/nordic/nrf54l15dk/nrf54l_05_10_15_cpuapp_common...
Hello,
I’m designing a wearable device based on the nRF52832. To maintain time and date when the MCU and other sensors are completely disconnected from the 3.3 V supply...
Hi, I have an issue with nrf52DK, I cannod flash new version of my software. I have an error in VS Code:
* Executing task: nRF Connect: Flash: Aurora-nrf52/Aurora-nrf52...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board. My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hi,
Has there any good course or training you recommend developing with LE Audio Development Kit either through Nordic official training or your preferred training program...
We observed a problem with our three different prototypes:
When there is only 5V-VBUS connected, the npm1300 does not ramp uo its voltages properly. The voltage rises up...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
Hi Nordic team,
I'm currently testing the nRF9151 DK with a Conexa IoT SIM card in the United States (Philadelphia area). The board is flashed with the Asset Tracker v1...
Hello,
I a doing a ticket because I don't understand why my dht sensor doesn't fetch with my nrf54L15DK board.
Here is my overlay file :
/*
* Device Tree overlay...
Hi,
I'm building a small Matter device and I'm in the very early stages of prototyping.
I'm using a MinewSemi ME54BE01 module on a custom PCB.
The development kit from...
