Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hello,
I am trying to get some basic examples working with my new NRF9151DK and running into quite a few issues. Note that this is using a onomondo sim card that came with...
Hi,
With NCS v3.1.0 and Nordic's downstream zephyr ncs-v3.1.0, I got build failure with following message:
--
warning: attempt to assign the value 'n' to the undefined...
Hello Nordic team,
After many hours I have not been able to get socket dispatching working with Zephyrs MQTT client, and I am not sure how to proceed.
First of all I would...
Hi Support Team
Due to there is very little space of C: drive of computer, so I moved the NCS SDK from C: drive to D: drive. The VS code can't recognize the SDK and toolchain...
There are 100s of solutions on the zephyr git and the nordic git. It took me a while to understand it all and it took me hours of debugging and frustration before I ended...
I want to work with the nRF Connect Plugin for VS Code and my nRF52840 DK with Zephyr. I created a new application from the "nRF Connect" plugin and selected the hello world...
Hello,
I perform a test using a nrf52840 DK board in order to output a PWM at 50 Hz on a GPIO.
Here is the code:
void pwm_init(void) { nrf_drv_pwm_config_t const config0...
Dear Nordic-Support,
have a question regarding nrfutil and the offline package generation, described here: https://docs.nordicsemi.com/bundle/nrfutil/page/guides/installing...
I am evaluating Curve25519 performance on the nRF5340 and have observed that the following operations each require approximately 2.5 seconds to execute:
- `wc_curve25519_make_key...
My customer had ttothis question:
We recently purchased and use your Nordic Power Profiler PPK2 at my company. Does this device come with any calibration certificates? How...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi all,
I was busy extending the asset tracker project and all of a sudden I got this lte rejection. First I thought maybe it the data limit has reached on the conexa sim...
Hello,
I've been having some connectivity issues w/ a multi-role application I'm working on. Essentially, whenever advertising is enabled, I am not able to establish a central...
I build code with the command
west build -b nrf52840dongle_nrf52840 and it builds fine, but I get errors when trying to Open DFU Bootloader E3FE4EE06DC5 with Programmer...
Hello,
we have produced 10 Boards with nRF9151. Unfortunately, 3 device shows a false behavior. We cannot connect over SWD an they have a larger power consumption (whole...
