Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi all,
I am using nrf52833 on a fanstel module BM833 with printed antenna. I am on NCS with Zephyr and my application is based on the nrf_dm example. Currently I can get...
I'm attempting to evaluate XIP (NCS 3.0.0) on the nRF53 with a mx25u256 flash chip. I'm placing a simple test function in external flash:
#define XIP_TEST_INC ( 100 )...
Hello, I am using the nRF Connect SDK v2.9.0. While working on the nRF52840 board, I used the library zephyr/crypto/crypto.h to perform AES/ECB encryption.
Part of the code...
I am evaluating the nRF7002's WiFi capabilities and starting off with the nRF52840DK + nRF7002EK and a project that connects to a socket and sends data. I've primarily used...
I have an nRF5340 project (that I cannot share) that uses zephyr, many modules, and a large application code space.
After much time crawling the VSCode extension javascript...
Hi
I used the throughput example in NCS3.0, and found that the rate decays greatly when the distance is farther away. And the rate is not stable.
I wonder if there is...
Hi everyone,
We are preparing for Japan MIC testing of our product and need to implement a special test program that meets the following requirements:
The program...
The customer soldered the 54L15 module to the TB-M54L15 board, unplugged the USB, and used the EVB's SWDCLK, SWDIO, 3.3V, and GND connections to perform earase and read operations...
Hello,
I currently have a product using the nrf9160, that started development 4 or 5 years ago. The firmware uses SDK 1.6.1, and whilst I have had to correct some bugs...
It's now two years ago, and the ticket had a different scope. But one of the answers from Nordic there was:
"This is because the spec mandates that if the device gets rejected...
I have installed the NRF Connect app on my Windows 10 PC, using "Run as Administrator" and keep getting the following error message whenever I try to install any of the products...
This is also my Bluetooth Prj.conf
When I turn on 2.4G, there will be an error message. How can I solve it? BLE and 2.4G cannot coexist at the same time. Can I switch...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
I'm using the NRF5340. When I open a standard example project located in the directory: nrf\samples\bluetooth\peripheral_uart (the well-known Bluetooth data transparent transmission...
