Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hello,
I using ncs v3.1.1 SLM on nrf9151 to send messages to a CoAP server. It seems nrf9151 by default uses AES_128_CBC_SHA256 even though on the server side, we have given...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
Hello,
Working on Ubuntu 22.04 with nRF Connect SDK 2.6.1 for the target nrf5340dk_nrf5340_cpuapp_ns (= with TF-M).
My application image became too large. I want to split...
Hi，
ncs v3.2.0，nRF54LM20-DK， I drive a buzzer. When the buzzer doesn't ring, I need a low level. I tried it according to the following method. I can't output a low level...
I need to generate PWM siganl around 4 mhz frequency but i did not get proper pwm signal and i got only millivolt range voltage this issue cuase i did not get proper audio...
Hello, I am developing with nRF5340 with my custom board. I observed a high current consumption when the network core is flashed with the ipc_radio image. I am developing...
Hi,
I am using NCS v3.3.0 and would like to implement the following setup:
Central: nRF52840 Dongle (connected to PC via USB)
Peripheral: nRF52833 acting as...
Hi Team,
Whether there is any configuration or option available to disable/eliminate signature verification during the boot process.
If disabling is not recommended...
HI
I need to implement LE Audio and voice KWS (Keyword Spotting). The microphone input needs to use two microphones to perform noise and sound filtering for sounds that...
Hello Team,
I am trying to configure pwm channel to a gpio in nRF54LM20B DK. I am not able to generate output using pwm channel. I have understood that here dts nodes...
The DECT Nr+ shell (the MAC version, not the -phy; tested with v3.3.0-ba167d9f3db4) offers IPv6 connectivity.
The DECT standard has a profile for IPv6 described in ETSI...
I wrote a simple terminal that reads the keyboard input from USB UART device and echos it back to the same device. It works as follows: 1. It registers an interrupt handler...
