Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
I'm trying to add a second element to (light_switch\server) (SDK_for_Mesh_v5.0.0). I've already have a look at this post , it gives an idea but I found that it's not applicable...
Hi,
Again the topic which has already been discussed several times in this forum. I just want to share my experience and perhaps help other users having difficulties.
...
I'm stuck trying to set my nRF Connect extension on VSC. I've followed the guide for the installation but I'm reaching a wall. Every time I try to install a given SDK I have...
Hi all,
I am currently testing on nrf52dk (PCA10040, 3.0.0) with NCS v3.3. Note: I also tested with vanilla Zephyr and see the same issue.
The code I run is to 100% the...
Hello,
I previously opened a ticket describing an issue where using MCUBoot in NCS v3.1.0 caused the GRTC to reset after a sys_poweroff() .
As discussed in that ticket...
Hi everyone,
I'm evaluating the nRF54L15 for a very low-power sensor node application powered by a Lithium Thionyl Chloride (Li-SOCl₂) primary cell. The goal is to achieve...
Hi,
I'm working on a project where I need to sample an ADC with an accurate sample rate. It essentially works except that I do not get the correct rate from the timer...
Device : wearable IOT device
Battery capacity : Max 4.2V (Typ. 3.7V)
BLE Tx Power : Tx power is highest when the battery capacity is 4.2V (measured in air, not conduction...
Hi, We want to use Sensibel microphones in a project with nfr9151, and it will be used to sample one microphone (mono) with 24bit data. This microphone seems to require 32...
Hello, Nordic Support!
I have some problems with programming my custom boards using my nRF54L15dk v0.9.1, when I use a setup with long cables (or several cables & adapters...
Hi,
I’m observing an issue in a Zigbee network where, after several hours of correct operation, the routers stop retransmitting the NWK broadcast frames sent by the coordinator...
Hi all! I need to see the printks and log messages from the b0n and cpunet app in RTT Viewer. The problem is, whenever I connect with the SEGGER RTT Viewer to the netcore...
Good morning,
we are using the Zigbee stack (ZBOSS) on nRF52 devices with Green Power Sink enabled and we are integrating a Green Power door sensor.
nRF5_SDK_for_Thread_and_Zigbee_v4...
Hi guys,
I'm hitting an error with the current Aliro 1.0.0 lib.
When a credential is signed today but its validFrom is in the future (e.g. signed=2026-06-17, validFrom...
I am doing some development on nRF5340 and I experienced MPU faults. We tracked down the root cause and this led to a PR https://github.com/zephyrproject-rtos/zephyr/pull...
In Zephyr 4.3.0, default swap mode was changed to use OFFSET instead of MOVE. As this is recommended by Zephyr as more efficient method, I wanted to switch to it but ran into...
mcumgr disconnecting when i trying to ble dfu .... " Log from nrf connect mobile app"
nRF Connect, 2026-06-16 FYZKS52_E23993 (E2:39:93:7B:81:AA) V 17:16:59.495 Connecting...
