Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
I have ordered two boards using the nrf52840
I was able to flash the first board and my firmware is working as expected however whenever I try to program the other one I...
When uploading a network core image though MCUBoot and confirming the image, sometimes it fails to accept and on other builds it accepts the update.
I have narrowed this...
Hi
Greetings, Hope you are doing well.
I am fairly new to using the nRF Connect SDK through VS Code. I completed the nRF Connect SDK Fundamentals course, and I also noticed...
Hi All,
I am currently working on an project with the nRF9151 using the nRF SDK v3.1.1 and MCUboot and I need to sign my application images using an external HSM. I am using...
I am having this problem in my Macbook Air M4. It times out when flashing the application via nRF Connect SDK extension. I also tried to run the nrfjprog command myself and...
I’m evaluating the nRF Connect SDK Bare Metal SDK and hit an issue with the bm_storage library. bm_storage_write() and bm_storage_read() work correctly, but bm_storage_erase...
When using GNSS periodic mode with nrf_modem_gnss_fix_interval_set() set to 20 minutes and nrf_modem_gnss_fix_retry_set() to 5 minutes, the actual wake-up intervals are inconsistent...
Hi,
I have a feeling we may be experiencing Modem Reset Loop Restrictions on some of our devices, so I want to put in something to our application code so we know and can...
Hi ,
I need to do create the bootloader . generally what we dump in to the board was the firmware not bootloader right. I want to do the OTA updates on the nRF52840 Dev...
Hello,
I am currently using nRF Cloud to perform FOTA updates on my nRF9160 devices. I have multiple certificates on this device.
1. TLS certificate for my application...
I need to store a hardware-revision value on an nRF9160 during manufacturing (using something like nrfjprog ), and the non-secure application firmware must be able to read...
Hi
I’m working with an NPM1300EK connected over I²C to an nRF54L15 , and I’m seeing an issue where the VBUSINSTATUS register consistently reads back 0x00 , even when VBUS...
Hi,
I’m working on nRF9151 with nRF Connect SDK 2.9.0 , and I’m facing a FLASH overflow issue when enabling dual-image OTA (primary + secondary partitions) . Our project...
Issue Summary
fds_record_update() in SDK 13.0.0 creates permanent duplicate records instead of replacing old records. This causes:
Valid record count to grow indefinitely...
Hi Nordic support:
Our project uses the nRF9151 and QM13545 MIPI RF SWITCH. We have a question about AT%XMIPIRFFECTRL command's frequency: If the frequency switching point...
