Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
HI
I am using nRF54L15 PDK with NCS 3.0.0. In my code, I am using NVS to store data on the MX25R64 flash on the PDK. The initialization code is as follows:
struct flash_pages_info...
Hello, I am currently working on a PDM microphone project using nRF52840 and Zephyr RTOS. I've been testing the official Zephyr sample (located at dmicncs/v2.9.0/zephyr/samples...
I have three questions regarding the electrical parameters of the NRF9151 chip:
For a GPIO configured as output: What is the maximum source current per pin when driving...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2. Because our terminal device 1 does not support using ble-FOTA, I used another terminal device...
Hi,
We have a custom nRF9160 board with chip antennas for LTE and GNSS. They are Ignion antennas with matching circuits customised to our board dimensions. We also use...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
I’m testing low-power behavior on an nRF52811 device.
When SoftDevice is not enabled , calling nrf_pwr_mgmt_run() gives me a stable ~5 µA average with no visible...
I am experimenting with ble_app_uart & ble_app_uart_c using two terminal windows, and I am sending a string of 1000 chars from the central to the device.
Although they are...
Hi Nordic
As information of nrf connect SDK, NCS3.0.0 ble_coex sample at NRF7002 DK can share single antenna for BLE and WIFI protocols.
It only needs to set "CONFIG_COEX_SEP_ANTENNAS...
I’m trying to use the Zephyr software split BLE controller ( BT_LL_SW_SPLIT ) on the nRF54L15 DK with NCS 3.0.1. I understand that this controller is not certified, but I...
I have successfully built an Auracast broadcaster transmitter using an nRF540 Audio DK and can stream to a pair of Samsung Galaxy Buds3 Pro with a Samsung Galaxy Tab S11 acting...
Hello, I observed this hebaviour on our own custom PCB with nrf5340: We would like to perform DFU over USB DFU class using dfu-util on the host. We tested our code on Thingy53...
I'm developing a device that occasionally bursts large data payloads (~30kB) over BLE. It uses MPSL to share the radio between BLE and ANT+, so I'd like the BLE radio to use...
Hi!
I'm developing an application that uses the bluetooth object transfer service.
I can transfer the directory list object (using OTS_OBJ_ID_DIR_LIST) from the server...
