I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
Hello,
There is a minor issue identifying a sysbuild configuration if the initial generate and build fails.
Steps to repro:
- add a kconfig that doesn't exist in...
In the past, I've been told I can bypass a lot of the Zephyr nonsense and use the HAL layers of the nRF Connect SDK directly. So if I want to use what was called nrfx_twim_xfer...
Hello,
I noticed the Audio application explicitly states that WAV sample rates other than 48kHz is not supported.
Is there any risk to modifying the code to support other...
Hello,
In my project, I use both a Bluetooth interface for communication and the PSA functionalities to store and read/use keys. I use the following configuration (excerpt...
Hi Nordic support:
Our product uses the nRF52840. During CE certification, the lab measured the BLE TX power in DTM mode. at –20 °C the power is 3–4 dB higher than at +25...
