Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Right now I am facing a problem as mentioned below:
I downloaded nRF52 SDK version 12.3.0. It contains lot of example code. I found .eww file in each example project folder...
I am planning start to develop new sensor base nRF52832.
My question is if it's possible to receive the.DSN file of the NRF52-DK board (development kit)
It will be very...
Hello All,
I am designing the custom board for Automotive application.I considered nrf51824 SOC for automotive application ,is this suitable soc for my application?if yes...
I have this program running on KEIL 5, what could be the problem with the code and Do you guys have any sample code for mcp9808?
Note- I am using the wired connection not...
I'm using SDK11 and PCA10028.
hrs works well, but did not bond with central(both android(kitkat) phone and iphone) in the nRF Toolbox app, althogh it's device manager ported...
I was wondering if anyone has done any extremely high speed UART work on the nRF51 (or the non-EasyDMA module on the nRF52). I need to improve performance for an existing...
Hi,
I ran the ble central example code on nrf51822 16KB ram version without any problem. But when I run the same code in nrf51822 32KB version, the program flow goes to 0xFFFFFFFE...
Working on my first project in mbed using the Nordic nrf51-dk.
The project utilises a TMP112 temperature sensor and attaches the reading to the service data to make it...
I'm trying to rename my device using s130, but the name doesn't get applied.
I went back to the "roots", ie the HRS sample.
Just before entering the loop, I add a name...
Hello,
I am working on a custom board with NRF52832-QFAA-R7 and trying to run ble_app_uart_c on it. I am using uVision 5.23.0.0
The first trouble that I am facing...
I'm trying to implement usb function on the nrf52840. The moment that I connect the usb to the computer the chip resets.
With gdb debugger i found out where the fault happens...
I have some question about ANCS ,when we trun off the IPhone and turn on the IPHONE.
The notifcation is disabled. I have to turn OFF the bluetooth and ON bluetooth form ISO...
Hi All,
I am a beginner,Can you please explain me what is the role of this line?
APP_ERROR_CHECK(nrf_drv_spi_transfer(&spi, m_tx_buf, m_length, m_rx_buf, m_length))...
Hi All,
I am using nrf51422, SDK 12.0.0, an SPI OLED display 128x32, and an SD card.
I want to interface an OLED display and an SD card onto the nrf51422. Although my...
