Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
When you start a receive task, what will the radio do if the HFXO is not stable? Not begin to ramp up until the HFXO is stable, OR begin to ramp up but not become active until...
nrf52832, returns an error even with parameters
IROM1: 29000 57000, IRAM1 3CC8 C338, softdevice_enable() works without errors.
#define PERIPHERAL_LINK_COUNT 1
#define...
im working on nrf51822 using sdk 9 ....i completed bonding using ble proximity example without privacy key.....now i wish to add privacy key ..what all changes i have to make...
I'm using the with SDK version 13.1.0 along with S140 SoftDevice v 5.0.0-3.alpha and trying to utilize the Bluetooth 5 Extended Advertising feature.
The function ble_advdata_set...
I'm periodically polling a TWI sensor with a blocking call, as in
ret_code_t err_code;
m_xfer_done = false;
err_code = nrf_drv_twi_tx(&i2c, address, subAddress, 1,...
My external application processor UART, every 5 ms @ 19.2 KBPS transmits a byte to UART RCV of NRF8001, which needs to convert this to BLE and then transmit to a cell phone...
Hello All,
I am working on nrf52832 and i designing the custom board for the same for my application , which all pins i need to select as programming pins to dump the code...
I'm trying to figure out why "some" (as in not all of them) Android Devices drop my Bluetooth Low Energy connection (to an NRF52 which I don't think is the problem) after...
I'm trying the example border router using 2 x nRF52840 boards one with CLI and the other with NCP connected to a PI. I can get ipv6 addresses and get them to ping each other...
Hi, I am trying to control an Omnivision Camera module using the nRF51822 EK. The module uses their proprietary SCCB protocol, which is very similar to I2C. However, there...
I am now using 52832 to do a project, need to send a BLE broadcast package first, and then start scan, what examples can I refer to?
Attachment is my TX/RX process，and...
Hello,
I always observe 4.0xxV from the li-po battery attached after when thingy52 stopped charging.
I think this problem maybe because of output current from the battery...
On our project we're using a Raspberry Pi 3 compute module with custom hardware and 2x nRF51 SoC running HCI from Zephyr.
We'll be delivering more than 150 of those devices...
Hello! Can I use one of the gpio pin as power source directly for other MC on my board (hx711 - ADC with current consumption in normal mode 1.5ma (from datasheet)). I understand...
