Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Hi,
I'm experimenting with the nrf52840 preview board.
I have tried the example "ble_app_att_mtu_throughput" using the coded option to check the extended range and it...
hi, everyone!
I have a question for pstorage, when i use pstorage_store,it was failed, return error code :15 how to solve it. Below is my code
void custom_flash_init...
With good luck, I traced my connection timeout to the slave/peripheral using nrfSniffer. What is most unusual is the slave unexpectedly stops corresponding with the master...
Hello,
I am trying to implement DFU secure bootloader to do firmware update over the air for nrf51822.
I have followed the steps as per the blog
devzone.nordicsemi...
Hello,
I want to ask, did the nordic chip support I2C slave ? I want to make other controller (STM) as Master and Nordic chip as slave in I2C.
Is it possible? or Nordic...
Hello!
I am trying to increase the MTU size to get higher speeds. When I increase the MTU above 65 the application locks/software reset when doing transfer. Up to 65 it...
Hi, I'm facing an extremely strange problem with a product I'm developing.
I've been getting significant idle current measurements (around 7 mA), and I couldn't for the...
I recently attempted to upload a new image via OTA.
After emailing the zip file to my iPhone as an attachment and tapping on it,
then tapping on the share icon several choices...
Hello,
I need a voltage regulator to power a microphone at 1.3V from a 3V coin cell battery and I was looking for a regulator like the lm317 , but with this one the minimum...
IAR EW 8.11.1 does not link the nfc samples from sdk 13.1. There are different sizes for wchar_t:
Error[Lt009]: Inconsistent wchar_t size
nfc_t2t_lib.o(nfc_t2t_lib_iar...
Q1 I compile sdk13.0.0 generate nrf52840_xxaa.hex(app), nrf52840_xxaa_s140.hex(bootloader).
I used merge tool make a hex file, then burn the file into PCA10056 DK by nrfjprog...
Hi Nordic and fellow developers,
I have been working on upgrading the nRF51822 QFAA s110 and upgrading the softdevice to work as s130 for its (simultaneous Central/Peripheral...
HI,
the solution I'm working on requires quite a few IO pins, so once I ran out of regular GPIO pins I had to resort to using NFC ones.
I changed the UICR registers...
