Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I have inherited a project where the Makefile sets __HEAP_SIZE and __STACK_SIZE for both CFLAGS and ASMFLAGS:
CFLAGS += -D__STACK_SIZE=2048
CFLAGS += -D__HEAP_SIZE=0
...
First of all I want to say hello. I'm new in nRF52 devzone and I have problem with ble_app_uart and ble_app_hrs programs. I use pca10040 board and eclipse for flash and debug...
Dear Guys,
I wonder if there is any possibility to have my ble as a scanning device but for softdevice version s110, I'm asking because I found all the examples are with...
Hi,
I am using ble-sniffer_nRF51822_1.0.1_1111_Sniffer.hex as the sniffer and I am trying to see all ble beacons.
Because I have many beacons about (100 in one second...
Hi.
In SDK 14.0 examples, there are two examples for pwm.
I analyzed both example.
pwm driver example source looks like that it use pwm peripheral driver source.
And...
Hello,
I would like to sample the battery level of my nrf52832 DK and send it through BLE. I have started from the example ble_app_hrs for SDK12.2 since the service was...
Hi,
Most of the sections of my application are functioning as I want it to, except these two (step 3 and step 4).
Application:
Connect device (with Auto connect...
I noticed while running a Bluetooth scanner app on my iPad, while testing one of my devices, that it was showing someone else's device in the locality.
What I found strange...
Hello!
I have:
nRF52840-Preview-DK (pca10056)
nRF5_SDK_13.0.0_04a0bfd (s140)
I load **nRF5_SDK_13.0.0_04a0bfd\examples\ble_central\ble_app_uart_c\hex\ble_app_uart_c_pca10056_s140...
I have an interrupt coming in every 50-150 microsecs and I want to measure these intervals as precisely as possible.
I tried this with SDK12.2:
APP_TIMER_INIT(0, 5,...
We're trying to bit-bang SWD to program an nRF52832, and we're running into some problems getting the nRF52 to respond. One theory is we're not generating a high enough clock...
i just purchased the www.xcluma.com/bluetooth-4-0-module-NRF51822-2-4G-module-development-board-ble-4-0 this xcluma nrf51822 module , so how can i progarmme it . which IDE...
