E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
How do you create hid information for a joystick and send it over BLE. Nordic doesn't seem to have
primitives for this (they have keyboard and mouse facilities). I'm working...
Hi Expert,
I use nRF52DK and SDK "nRF5_SDK_12.3.0_d7731ad_test\examples\ble_peripheral\ble_app_hids_keyboard"
I saw many NRF_LOG_INFO and infocenter said should have many...
Hello,
I want to change the TX address or channel "on the fly". Since this did not work for me, I read the following post: "Is it possible to change TX address on nrf24l01...
Hello everybody!
How can i read the temperature, the battery-% or other data from the Thingy when using the Linux console and not the SDK? My steps so far
1. With i was...
I am estudying and modifying the light switch example.
the example shared in the SDK, this example works as star network. (1 client and 3 (or many) servers) where:
- The...
Hi,
I' writing an app based on ble_thread_dynamic_template with added CoAP utils, but with a few changes. Program works fine, I am able to communicate over CoAP, but after...
Hello!
Last time I've described issue with connection problems in large thread network https://devzone.nordicsemi.com/f/nordic-q-a/29867/thread-mesh-network-capacity-problem...
Hi,
I have encountered a 404 error:
<<<
HTTP ERROR: 404
Problem accessing /help/pdf/nwp_017.pdf. Reason:
ProxyServlet: /help/pdf/nwp_017.pdf
Powered by Jetty...
Hi,
I am trying to send stream of data over BLE. I am using nRF52 development kit and in that ble_app_uart code is running. I want to send continuous data to the UART and...
I am using PPK 1.1.0 to compute current draw on a custom hardware.
If I upload ble_app_hrs example on the nRF52-DK and measure it directly, I obtain average reading as 550...
Dear all,
sorry for asking a very beginner's question but I'm really a beginner and want to understand what I'm doing :)
What I have:
nrf52 DK
nrf SDK11.0.0...
Hello,
we are using the USB CDC ACM Example to set up a USB connection between the computer and the nRF-Chip.
By pressing Press Button 1 a bunch of test data will be sent...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
