Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello everyone,
We want to do nRF51822 OTA DFU by using another nRF51822 only. we have done OTA DFU with help of example given in SDK and with help of mobile app(nrf toolbox...
I have a project I've developed on a dev board, and everything works. When integrating this into a custom board and running the firmware, however, I'm not getting any BLE...
i am working on mesh application in nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for SDK...
i am working on mesh application in nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for SDK...
Hello,
I am using custom board with nRF52832 and Keil uVision5 as IDE. I started with simple example which is just to ON the LEDs.
Code(all necessary header files are...
Hi,
I'm developing a FW that is now validated. We are "almost ready" to go in mass production (6000 PCE for the first batch).
For the moment, I'm still using the debugger...
Hello,
I am using the mesh pb_remote example in order to have a multihop scenario. I would like to do some latency calculations, so some kind of bidirectional communication...
Dear all,
I'm using NRF52832 with SDK 14.2.0 and SD 132 v5.0.0.
I have my own implemented application working properly when is flashed directly without bootloader, only...
Hi,
I'm wondering if anybody has performed a test of, or has experience with Nordic Semiconductor thread mesh stack (nRF5 SDK for Thread and Zigbee v1.0.0) in a large scale...
Hi, i used the 'nrf5_SDK_for_Mesh_v2.0.1_src\examples\light_switch' i have two question:
1: How to added more Client in one mesh net?
2: How to configuare node to 'low...
I am trying to make RF USB dongle using nrf52840.
Before the PCB production, we are using DK to test, but the firmware is not uploaded because VDDH and VBUS of DK are connected...
Hello Nordic!
Sometimes we have a problem with a services discovery. We have no custom services. Only DIS, BAS, NUS and DFU. (nRF52832 and SDK15)
This problem is currently...
Hi,
I'm working with the light_switch example on Mesh 2.0.1 and I would like to modify the simple_on_off_client_set_unreliable function to broadcast to all servers in the...
I am evaluating TAIYO YUDEN board EKSHSNZWZ.
I've flashed s132_nrf52_5.0.0_softdevice.hex using nRFgo Studio.
I use Keil uVision to test "nRF5_SDK_15.0.0_a53641a\examples...
