Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am estudying and modifying the light switch example.
the example shared in the SDK, this example works as star network. (1 client and 3 (or many) servers) where:
- The...
Hi,
I' writing an app based on ble_thread_dynamic_template with added CoAP utils, but with a few changes. Program works fine, I am able to communicate over CoAP, but after...
Hello!
Last time I've described issue with connection problems in large thread network https://devzone.nordicsemi.com/f/nordic-q-a/29867/thread-mesh-network-capacity-problem...
Hi,
I have encountered a 404 error:
<<<
HTTP ERROR: 404
Problem accessing /help/pdf/nwp_017.pdf. Reason:
ProxyServlet: /help/pdf/nwp_017.pdf
Powered by Jetty...
Hi,
I am trying to send stream of data over BLE. I am using nRF52 development kit and in that ble_app_uart code is running. I want to send continuous data to the UART and...
I am using PPK 1.1.0 to compute current draw on a custom hardware.
If I upload ble_app_hrs example on the nRF52-DK and measure it directly, I obtain average reading as 550...
Dear all,
sorry for asking a very beginner's question but I'm really a beginner and want to understand what I'm doing :)
What I have:
nrf52 DK
nrf SDK11.0.0...
Hello,
we are using the USB CDC ACM Example to set up a USB connection between the computer and the nRF-Chip.
By pressing Press Button 1 a bunch of test data will be sent...
Hi!
Is there any programming guide for establishing mesh network? I want to develop from scratch but i can't find any document for programming to mesh network. I seen Light...
Hi
I am able to successfully compile my C++ code on Raspberry Pi3 however while running an executable file. I am getting below error.
pi@raspberrypi:~/RF24/librf24-rpi...
Hello,
I would like to send an int32 value every 500ms and use for this the same procedure as it is shown in the heart-rate-example. The code for sending is:
// Send value...
Hello Nordic Devzone fellowes
I tried DFU with NRF 52 DK board with 'PC-BLE-DRIVER-JS' dfu.js test code
When the firmware .zip file is 128 KB the speed of transftering...
Hi, Everyone
I am developing based on ble_app_uart at nrf52832 (softdevice s132)
I modified the program slightly.
- After the connection is confirmed
- Send 100 bytes...
Hi Devzone:
I have build up a environment that are
1. a thingy52 with mesh-briadge
2. a thingy52 with mesh-node, which is control by segger-debugger, and it shows
...
