The partition config for ZBOSS is set in different locations in NCS. For us this worked out magically in the past because the values that were written have been the same in...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
I have been playing around with the configs but I could not get Mode-3 to activate. What should I change for cs configs and the prj.conf file in order to activate it...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
Hi All,
We have build a BLE beacon device based on the nrf52 chip. The device works fine but we would like to get a finer control over the TX power since it is used for...
compiled nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_rscs example but will fail on adding chararteristics in char_add() setup: SEGGER Embedded Studio for ARM Release...
Hi guys,
I am trying to use a TM2001 amplifier ( Taiwan Microelectronics, google returns the PDF) to amplify the signal from an nRF24L01P.
The TM2001 seems to accept a...
Hi.
I want to create Bluetooth mesh network and I need that each of device at first must be provisionee, but if in a minute it hasn't been added in a network by provisioner...
Hi
I was designing a custom board for nrf52832. The 32MHZ crsytal mentioned in the refrence design of nrf52832 is not available on digi key. So I am ordering the below given...
Hello,
I have a string data and I want to get a part of it which start for example with "hello" and I want to get 20 characters after "hello".
(for more details I'm using...
in the demo of EnOcean switch translator client,there is just enocean_switch_nrf52832_xxAA_s132_6_0_0.emProject .is it use the same demo as client in the example of light...
Hi, I am using nrf SDK for mesh and try to add FreeRTOS , but after adding build failed because both has files with same name. Is it possible to work with FreeRTOS and nrf...
Hello;
I want to scan beacon devices (UUID infos) every second with Arduino Uno + nRF51822
I could not find a sample on the site. (Arduino Code)
Is it possible? Would...
I've gotten a good handle on how Gazell interacts with devices and the host, but I am running into an issue where there are higher rate of failures when using two devices...
I am using the proxy server and the proxy client example
Initially Proxy Client and Proxy Server are present in MESH network. Once the Proxy Client recycle the power ...
