Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I try to port LESC example from PCA10040 to PCA10040e(52810) on SES.
Porting work has been done. When building, it reports VFP issues of liboberon_2.0.4.a, as below:
...
Hello all,
I am using the latest SDK 15 and softdevice v5 (downgraded from v6 thought it was causing issues) on the NRF52 DK. When I build my application it states:
Compiling...
I want to make my device automatically go to sleep mode when the power is connected. And when the device wakes up from sleep mode, it should not automatically go to sleep...
Hello, We are trying to use the debugger tool on Keil for the nRF51 DK, But we are having a really hard time to figure out how to make it work. Do you guys have a tutorial...
Hi,
I am developing my own program based on serial example. Project is based on gcc compiler under eclipse. I have preapared my own board with rigado module (nrf52832). HW...
Hi!
SDK13, nRF52.
I try to use FDS storage to flash and always get FDS_ERR_NO_SPACE_IN_FLASH.
What shold I check for normal work?
Now I have next settings:
#define...
Hello,
We are having a peculiar issue with the NRF52 and SDK 13 that I hope you might be able help with.
Having migrated from SDK 12 to SDK 13 with softdevice 4.0.2, we...
Hi,
Im having nRF52 DK and im using CLI example....i have configured through the putty by seeing this https://devzone.nordicsemi.com/f/nordic-q-a/22261/cli-autocomplete...
I implemented DFU secure ble. And implemented encryption. But now I remarked strange behavior. If make same DFU packet (.zip) and flah nRF52 than update firmware for same...
Hi,
Im running CLI program in my nRF52DK.
Im unable to connect using UART or USB as the transport layer for the CLI module but i can able to connect using RTT as the transport...
Hey!
I have some trouble service UUID then i try to use the multilink central example project on a nRF51 dongle. I want it to have contact with a peripheral with sends a...
I'm trying to get a Bluetooth interface (Bluefruit) to the Nordic BLE softdevice under NuttX. Right now it's very unstable. It will work occasionally for 90 seconds and then...
Hello,
When trying to connect to our custom board, it ends in Time out after 5 seconds.
On the board, I put the simple Nordic_Blinky example (\examples\ble_peripheral...
