Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi,
We are trying to have control on firmware update of our BLE mesh network. As a starting point I have ran the light-switch examples and DFU over mesh example. In light...
We are develop one product, it is power by four AA battery. It works fine. but now I found a problem. when I power off and then power on again, sometime it can not be reset...
when I start ADC the current will be HIGH .even I UN-Initialization it .
what I have done like that below；
before I started it The current is 0.6ma
but when I start...
I'm trying to communicate with a device over UART, and I'd like to return the response to my commands back to the function the transmission came from.
For example, I want...
I want to develop nrf52840 with ble mesh topology.
However I need one node to transmit data received from all the nodes via uart to a gsm module
Can anyone please tell...
Hello Nordic experts,
I am trying to use app_usbd_ep_enable and app_usbd_ep_disable in order to enable/disable an endpoint. I need this to fake usb unplug/re-plug. Currently...
Hello. I am testing the sending and receiving of UART using nRF 52840-DK. If you change the UART pin settings as follows, you can receive but you can not send. It is confirmed...
Although I have already seen this discussion ( https://devzone.nordicsemi.com/f/nordic-q-a/35183/no-idea-how-to-get-manufacturer-specific-data-in-central-side-from-advertising...
Hello,
I have an nRF52840 chip ( Holyiot nRF52840 module ) and I want to program the chip using an nRF52840 DK. The Holyiot module is basically an nRF52840 mounted on a...
I am having trouble turning on bonds for DFU.
First of all, before I describe this pain, can I choose to avoid this battle by just allowing unbonded devices to DFU? e.g...
Hello!
I just bought the Beacon Kit and i was following the user guide v1.1 and I have some questions about how to use DFU. I have already downloaded nRF Toolbox app.
...
Hi,
I am using fatfs of nRF5_SDK_15.0.0_a53641a. I am writing a program with keil.
I want to know how to write the value obtained from the sensor to the SD card. ...
I am using proximity profile in sdk15 with softdevice 6.0.0 . I added flash write, writing continuously some data to flash. But it working sometimes only.
