Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
when message relay by any node how can other node know that it is for him and update status.
for example if I subscribe some nodes to 0xc001 group and others to 0xc002 group...
Hello,
I am making a PCB for my project using the nRF51822 chip? Can I power a LED with the GPIO pin or do I need to connect a MOSFET to drive the current? Also, I want...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
hi,
I'm trying to merge the the proxy server and beaconing example together. When I compare two main.c and copy the advertising part from beaconing to proxy server example...
Hello everyone, the sdk version that I use is 15.0. The soft device is s132.
With the example of peripheral/uart I am able to receive the serial uart sensor data. On the...
Hi Sir
I'd want to send DTM command by hard code, but I don't know where is the command spec for reference ?
Has any one could show me where is the spec ? and give me...
Hi,
I am using nrf52832 with soft device 3. I am operating on peripheral role, while i am initiating sd_ble_gattc_exchange_mtu_request with desired MTU ,it internally sends...
Hi! I am using SDK15.0 and SD 132 v6.0.0. My IDE is Segger Embedded Studio.
Everything was working fine and then suddenly after few weeks of developing a problem appeared...
Testing BLE mesh of proxy light switch example with 3 nrf52840(1 as client and 2 as servers) pdk boards with nrf mesh apk(android phone). Phone able to scan nrf 52840 light...
Dear Team,
I am using ST-Link V2 connector to program a nRF52840 board. When connected to a laptop and try to connect to the target, it says 'ST Link USB Communication...
I am currently trying to extend the range of the bluetooth mesh application. The infocentre infers that the function:
typedef struct
120 {
121 radio_tx_power_t tx_power;...
Hi,
I wonder if someone can make recommendations for types of 'smart bracelet' ('smart wristband') devices that use a BLE chip of Nordic's nRF51/nRF52 range. Can you point...
Hi,
I'm currently developing software on nrf52832. Unfortunately, I can't use the SDK for different reasons.
I'm currently looking at the RESETREAS register. If I...
I use the following code to write 32-byte to L01-module. (The wireless-communication works successfully ).
The following ( 420us+200us ), accompany only 32-byte wireless...
