Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
-HI.
I had previously implemented ESB RF communications with the nRF24l01 + and nRF24LU1 +.
Now we want to implement ESB RF communication with nRF52840 DK(PTX) and nRF24LU1...
Hello,
I am trying to evaluate the "ble_app_uart" in the "nRF5_SDK" and I am using "DVK-BL652-SA-01" development board from LAIRD.
The example works fine for a while...
Hello,
I'm using the "ble_app_uart" example without a problem. I need to add a timer to this example. For this purpose, I copied the content of the " peripheral_timer" example...
Hi,
I’m working on a project where I need to control a device via BLE_Uart. The scenario I’m trying to achieve is: - I have a network of several centrals und several peripherals...
Hi, I'm trying to use Atomic FIFO in my application, where multiple interrupts of different priorities are trying to read from and write to same FIFO. I couldn't find any...
Hi,
The questions:
When is PB-GATT expected to land in the SDK for Mesh?
What are the best Andorid/iOS example apps to act as provisioner and network...
nRF Connect suddenly can not find the COM port to my nRF Dongle. The same setup used to work fine untill today. I reinstalled the nRF Connect, JLink drivers but it is still...
Hi,
I'm using SDK 15.0.0; nrf52840 DK; IAR(EWARM).
I want to add TWI(i2c) from example in SDK to my project.
But I facing with next errors:
Error[Li005]: no definition...
Hi dear engineers,
I have a strange TWI problem on my production protype which programmed based on the official twi example with softdevice s130_nrf51_2.0.1 and SDK 12.3...
Hi,
I'm trying to schedule few events within the shortest connection interval . Is it possible to shcedule 3 events, 2.5 ms long within 7.5 ms connection interval? Could...
Dear all,
I am using the nRF51822 custom developed board. Earlier it was working fine, but now when I try to connect the BLE with nRF ToolBox APP UART service, the APP...
Hi,
Have flashed an early sd_power_system_off first line in main() when measuring power-consumption...
Now the SWD access seems gone. Is there a trick to get it back in...
Hi, I'm working on a custom board with a nRF52840.
I want to use REG0 and REG1 as mentionned in Figure 13 of the datasheet : with VDDH, and both DCDC. My PCB is powered...
