Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
Hello all,
How does the handling of ble events work with SDK 15.1? When I register more than one event handler with the macro NRF_SDH_BLE_OBSERVER(), how does the softdevice...
Hello Support team,
I'm working on a project where I am designing a custom board uisng the Nordic NRF52840 as the MCU (forgive me if I'm using the incorrect terminology...
Hi,
I am relatively new to programming hardware at this level, and have developed our product on the 52832, so finally I have purchased the Power Profiler Kit, and downloaded...
Hello good morning,
I am using nrf52840 device. I am sending 20 bytes using notification at different notification intervals like 30ms, 80ms and 1sec. But at application...
hello
I am currently trying to use the thingy_52_sdk sample code to embed a program using the J-link debugger with the Nordic thingy 52 development kit. But the build is...
Hello,
I am attempting to test slew of Rigado BMD-350 module BLE radios (uses nRF52832) using a Rigado BMD-301 series Eval Kit to act as the central. The BMD-350 device...
Hello everyone, the sdk version that I use is 15.0 (nrF5_SDK_15.0.0). The soft device is s132. In the ble_peripheral / ble_app_uart example you can only connect through the...
If followed the following steps:
Installed Win10Pcap
Installed Wireshark-win64-2.63 on Windows 10.
Using nrfGo Studio loaded sniffer_pca10040_51296aa.hex (after erasing...
Hello fellow Nordic Community,
We have a usecase in which it would be beneficial with a tx power of - 30 dBm . This is a value that was supported with the nRF51 chip series...
Hi,
I am develop a project with dfu and bond features. I found that in dfu project, IS_SRVC_CHANGED_CHARACT_PRESENT is always set to 1. In my understanding, if set this to...
hi,
i am using Nordic thingy:52 with a nRF52840 with s140 softdevice to receive multiple characteristic data from thingy like thingy environment service have 6 characteristics...
Hi,
Is there any way to stop the OTA DFU? Let's say that I started it and at some point I want to cancel the process at 40%. Is there any way to send a control message to...
Hello fellow developers need your help
I have bought 3 nRF52840 dongles and want to setup a mesh network as stated above. I have downloaded nRF Connect windows application...
From this ( https://devzone.nordicsemi.com/b/blog/posts/measuring-lithium-battery-voltage-with-nrf51 ), there is capacitor connected to adc input pin.
But is it necessary...
The device I am building requires a quantity of data to be loaded into the application data block so that it can be accessed at run time. The data is effectively calibration...
