Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Using some of our nRF51 dongles as sniffers to debug BLE.
Sniffer software --> "w" --> Wireshark, no problems.
Post processing wireshark export *.csv files. No problems...
Hi.
Is there some code example for Bluetooth button for PTT aplication Zello ?
When I press a button BLE should send notify event =1, when released BLE send notify event...
I'm building battery power BLE mesh network the nodes mast have the publishing period match greater than 5 minutes. And my question is how to estimate the power consumption...
Hi, I have a spis problem when nrf_drv_spis_buffers_set is called, it enters the switch on the SPIS_BUFFER_RESOURCE_CONFIGURED case, then calls spis_state_change with SPIS_BUFFER_RESOURCE_REQUESTED...
Hello,
I'm using the examples light_switch_server_nrf52832 and light_switch_client_nrf52832 to send data over Bluetooth Mesh. Using the description from creating new models...
In the SDK the multi protocol example switches back and forth between Gazell and BT with a button press. Is it possible to maintain a BT connection and a Gazell connection...
Hi,
I have a quick question regarding isochronous data transfer. This type of transfer is still in the draft but are there any hooks in SoftDevice that would enable us to...
Hi I'm brand new to use nrf52840, but hope there is one that can help i need a counter / timestamp. If it's a counter, it still has to count even if you do something else...
Hello Everyone,
I am using Martinsbl / nrf5-mpu-examples nrf52-mpu-easydma-using-timers-and-drivers. When I tried to change the TWIM_RX_BUF_WIDTH to get the gyro data, the...
I'm totally new to Nordic solutions. I was programming a lot in assembler in 8051 era 20 years ago. Now I feel lost in that new solutions.
I have PCA10040. It is connected...
Hi everybody
I'm working on an application where I want to sample microphone data with the adc (NRF52 DK board, nRF52832) and send it over BLE to a central device. I've...
Hello, we just made a raw board with the MDBT40, which use a nrf51422 chip. I downloaded SDK version v12.3.0 (which supports nrf51) on the nordic website. With nrfGoStudio...
Hello, I am trying to use the 'nrf51-pwm-library ' on mBed with a nrf51822 on RedBearLab Nano.
I copied the nrf_pwm.h/c files and they compile, but I never get any sort...
Hello everybody ! Designing with the development board nRF52832 and SDK14.2.
My code is based on the code of the "ble_app_multilink_central" on which, I added some of the...
