I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
Hello,
I'm trying to port my application from the nrf52832 to the nrf52810. I'm using the Fanstel modules, originally was using BT832 and am now trying to bring the application...
1.What are the dimensions of the NFC antenna (component A1) for the reference designs given in the design files here
http://infocenter.nordicsemi.com/pdf/nRF52832-CIAA_Ref_Layout_v1...
Hi,
As showed in the code, I masked " else if (m_nw_state.provisioned_devices == 0) ", then it reported "NRF_ERROR_NOT_SUPPORTED".
Can you tell me how should I do...
Hello,
I didn't manage to run PA/LNA switching with softdevice (function: sd_ble_opt_set(BLE_COMMON_OPT_PA_LNA, &options)) with P1.* GPIO pins.
Note that all P0.* pins...
Hi,
Is there any chance that we can completely turn-off the radio part of nRF52832 and only the application part of the processor running. Also, we should be able to turn...
Hi,
I would like to program and debug a code into the Nordic Thingy:52. I read that I should have either J-Link or nRF52 DK. And I have the nRF52 DK, but I don't know...
Hello all,
I'm working with the nRF51 SoCs, with the s130 SoftDevice and SDK12.1.0
I have a BLE Nano from Red Bear Lab that has a nRF51822 doing adv and it expose...
I want to put application, softdevice, and bootloader into one hex file, after doing research, I think I need bootloader settings page to make the application run. I get the...
Hello,
I have been using another vendors mesh stack to develop a product that uses mesh networking, however, their stack is limited to storing provisioning data in a certain...
I'm trying to set up DFU for a custom board with a nRF52810 module (Rigado BMD-330). I created the secure bootloader from the recent project for SDK 15 posted by Vidar Berg...
Hello!
The NRF52832 uses the QFN-48 form factor but I'm having some problems finding it in Fritzing. Did some made their own, know where I can find it? Fritzing has QFN...
Hello,
I'm using SDK15.0.0, device nRF52832 and softdevice S132.
After open "secure_bootloader_ble_s132_pca10040_debug-nrf52832_xxaa_s132" project and build it, I got...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
When initializing a UART instance (0 or 1 or both together), the current consumption increases to 600 μA
Then deinitialized UART, but consumption is not reduced!
- I tried...
Hello everyone!
I've had an ESB application running o the nRF52832 for more than a year. When I moved it onto the nRF52840 it no longer works. There are no changes to the...
