Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello,
i follow this example " https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic-DFU-to-a-SDK-Example " to change ble_uart_example (enter new library...
Hello,
With the last environnement version, there is a potential issue
CMake Error at F:/Git/YYY/Projects/ZZZ/TTT/nRF_SDK/ncs/zephyr/cmake/extensions.cmake:395 (file...
Hi, I have built an nRF52832 application using SDK15.3 / S132 6.1.1 that runs on E0 chip revision (development board). If I program B0 chips (production boards) with it, it...
Hello, I encountered a problem during my development. My phone is paired with MITM and pin code security. I enabled the service changed indication to indicate the smartphone...
SDK ver：15.2.0
demo：usbd
i want to use the 52840 usb function ，the pc is the host ，the 52840 is device。
i cant use respond_setup_data to send data to pc。
but how to...
Hi All,
I am using nRF52840 for product development , there is a issue on measure the TX power .
Now , my firmware is development with softdevie, I want to comfirm my...
I am a newbie to Nordic thingy and Keil. So please help me with this.
I downloaded SDK and opened it in Keil. It asked for updating software packs update and it was
done...
Hello expert,
I follow the steps with this tutoriel " https://rigado.zendesk.com/hc/en-us/articles/360025376053-Add-Nordic-DFU-to-a-SDK-Example ".
I reach to the DFU...
Hi
I made a custom board. (using nrRF52832)
At frist, I tested my code on 52DK(PCCA10040). It is worked.
And then I tested my code on custom board. I changed my code...
Hello,
Sorry for simple question. (Yup, I'm Canadian and we say sorry a lot!) I have SES 4.18 and nRF5 SDK 15.3.0 installed on my Mac (10.13.6) and cannot get logging (NRF_LOG_INFO...
Hi! I am using the MQTT simple sample that i have modified to continuously send data after receiving a message. I also have connected a MS5837 pressure sensor to the nRF9160...
I'm trying to get DFU OTA working with SDK 14.2.0, SD 132, on the nRF52832. I'm using the bonded implementation. My DFU event handler is getting passed
BLE_DFU_EVT_BOOTLOADER_ENTER_FAILED...
So I want to run the nRF52811 chip so I removed the nRF52832 chip from its development kit and soldered the nRF52811 chip but I cannot seem to program it. What are the required...
Hi,
I am using ncs 1.0.0 and modem fw version 1.0.1.
I am using PSM mode in my firmware.
I want to toggle state of one gpio when modem goes in active or inactive state...
