Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
It seems NB-IOT can work on different modes according network operator condition, is there any way via AT command to interrogate the nRF91 to know the "operation mode" and...
Hello,
I just created an application that can count the number of rising edges/events on button presses using the TIMER0 peripheral configured as a COUNTER. So far it is...
I am developing an application for Android and IOS. Faced a problem when try connect nRF Connect as central (on Android) to nRF Connect as peripheral (on IOS)
...
What I need?
I should be able to perform scanning, connecting, disconnecting and accessing service from main() (in a infinite while loop) rather than interrupts. I see that...
Hello,
I'm using SDK16 with the s332-6.1.1 softdevice in ANT mode.
When I request a radio timeslot of 10 ms, that works just fine, but if I do anything longer than approx...
Hello,
we have developed a custom board using the nrf9160 SICA chip and are now modifying the bifravst cat tracker example to suite our needs.
Basicaly, it samples from...
I am trying to get my ublox module to respond to at commands, through the programming of the boron module, which is found in this link, but I don't have much idea of how...
Hi.
I am trying to get mesh DFU working and I keep getting "Failed to upgrade target. Error is: Crashed on start packet" from nrfutil.
When debugging the target I see...
I am using the nrf51822 ble with softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such as I want to...
Hi Nordic Community,
I'm trying to run app timer in bootloader_secure. But when I add app_timer.c file to project, it built successfully but breaks when execute. I don't...
Hello,
I am using a custom nRF52840 ( SDK 14.2.0, SoftDevice S140) based board to connect with an iOS(v 13.3) phone.
I am sending data continuously over BLE. However I...
Hi,
I'm trying to find simple ADC code for one shot modus as described in the documentation: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52832...
I will use Nordic nrf52840 dongle for 2FA + security key on Google login and I am following these instructions:
https://github.com/google/OpenSK/blob/master/docs/install...
I use nRF52840 and SDK16 with S140 softdevice. I need 3 ADC ports. The initial code as follows.
static void adc_configure(void) { ret_code_t err_code = nrf_drv_saadc_init...