Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi everyone, I have a custom board in nrf52833. Currently, the gpios on nrf52833 are gone, except for the NReset pin (P0.18). Can I configure the NReset GPIO as a GPIO I/O...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hello,
I am using Segger Embedded Studio to run AWS FreeRTOS bootloader demo on the nRF52840. When I try to build, I get the error cc310_bl_backend_ecc.h: No such file or...
the first (initialized) Eddystone (e)TLM frame have vbatt unset. I am using SDK 15.3. I suggest the following changes, it simply busy wait until ADC reading is finished before...
I had been programming custom boards with the nRF52840 DK both through nRF Connect and the Command Line tool without issues. I have shorted SB47 to provide power to the target...
Hello,
I am see odd behavior with SES and git repos. I was working on a branch and wanted to confirm there was no issues with the building the project before I started adding...
I am sorry to ask a stupid question as i supposed to fix firmware issue with my zero knowledge.
Before android app (central) connected to peripheral ble 52832, If I press...
Hello,
We have developed a GATT based application based on nRF5_SDK_15.0 (Bluetooth LE without mesh). We want to add mesh functionality in this code as you described in...
Hi, I am new to Nordic devices. I have purchased Nordic Thingy91 (PCA20035).
I need a small clarification on the programming/flashing the nRF9160 and nRF52840 on Thnigy91...
Hello
I am trying to operate the ble_peripheral_hrs example found at SDK 5.11 (several years ago) for Segger, but I can't found a project (*.emproj) for it.
Have you know...
Hi,
I have nrf52840 on my custom board (Based on IMX6, Running Yocto linux) which is connected over UART.
I want to an OTA of zephyr OS on that chip over serial and for...
We have a custom device that we profile with a PowerProfiler (external DUT). Device is battery powered.
We have a strange idle current: cca 5 uA for 2 min, then 900 uA ...
Hello,
I am new to the nrf9160. i am quite confused in between nRF Thingy91(pca20035) and nRF9160DK (pca10090) .
What are the steps i need to follow to get start with...
Hello:
I want to change uart0 tx and rx pin from default 28 and 29 to 10 and 11.
I know the i2c pin change need to change nrf9160_pca10090ns.overlay in app.
So I tried...
For quite a while I've noticed that across multiple custom boards using the nRF52 I've been seeing low-level current spikes from a part that is in SYSTEM_OFF mode. They are...
i got 'LIS2DH12_ADDR' undeclared (first use in this function) error when i build my project but i already define it in pca20020.h file.
this image is i define about...