There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
we are using MQTT to push the sensor and GPS data with 1 hour interval. After 4 consecutive connect and disconnect, MQTT is returning socket error. It requires the device...
Hi,
I am using NRF51822 SDK12; S130 and trying to qualify Batter level service with the SIG's PTS device (dongle)
So far encountered a problem with Test Case: BAS/SR/DES...
Just got a nRF5340 DK, testing on macOS 10.15.2. Setup was smooth – the nRF Connect assistant is pretty good. The only feedback would be that an explanation of the "Variables...
Hello Nordic Team,
I'm currently working on a project based on the nRFready desktop. My application requires using the pipes 0-2: pipes 0 and 1 are used in conjunction with...
Hello everyone!
I want to use the app_sdcard to read/write with fatfs on a uSD card in my app which is based on FreeRTOS. While i was implementing this library, i saw that...
Hi,
I would like to know, where the packets are written into the flash for the mesh DFU example.
In nrf_mesh_dfu.c is a function nrf_mesh_dfu_cmd_send:
It calls...
Hello,
I have a little issue during the mesh configuration of my network.
First my provisioner (called master) provision and configure a first node (called slave), this...
I have downloaded project from https://devzone.nordicsemi.com/f/nordic-q-a/55710/while-building-thingysdkv210-on-segger-showing-error-thingysdkv210-source-modules-thingee_ble_handler...
I am using Nordic's nRF52840 DK board.
I wanted to sync time on End Device(nrf52840DK Board) via sending packets to it. What should I do?
what clock/rtc library or API...
I am sorry but this is totally BS. I just got the Thingy 91 and it does only problems...
I have no problem using a full day on getting stuff like that to work, but please...
I am currently developing a device and would like the default behavior at boot to be:
1. Boot up
2. The device should start advertising for non-bonded devices.
3. When...
Using the 15.3 SDK and the 6.1 software device I am successfully changing the transmit power as needed. When not connected and advertising I would like to update the advertised...
hi
i have a problem with 51822.
i test my production, power on /power off again and again.
maybe 51822 can not work. but is too hard happen.
My code is at main output...
