I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello! Just started looking in to using whitelists and looking for information in the infocenter but the "advertisement module" is inaccessible on NRF SDK v15.0.0/libraries...
I'm working on a solution that will need to acquire GPS location and backhaul that to the cloud over LTE. I'm trying to figure out whether it makes more sense to go into PSM...
Hello All,
I am measuring the nRF9160 current in the sleep mode(program with just k_cpu_idle(); command) but still I am getting 530uA current. I have also tried to change...
Hi,
We are using ncs 1.0.0 and modem fw version 1.0.1.
We are currently using 2 UART, 1 SPI and 1 I2C peripheral in our application.
We want to use one more UART in...
I merge all hex file of Bootloader, Bootloader Settings, SoftDevice and Application with Buttonless DFU code included into one hex file. After that, i recover the device....
Hello Nordic team,
I am trying to get my product read for FCC/CE compliance testing. I came across the radio_test example and other examples posted on DevZone. I have the...
Hi,
I have just recently started to develop an NRF52832 chip with Keil uVision 5.
My setup is the following:
PCA10028 Development kit connected to Feather NRF52832 bluefruit...
Hi,
We are planning to add an external flash to our nrf52840 based design.
The flash type is
http://www.puyasemi.com/uploadfiles/2019/06/20190604154800480.pdf
I'd...
I used This char tutorial for this project. Basicly I added beacon advertising mod with a connection mode to this project and I tried to changed minor and major of the device...
Hello! Something strange is happening with my nrf51822.
I have a simple code to obtain data from the ADC and send it through BLE.
I do the following in the main loop:...
Hi,
I am new to Nordic Thingy91.
I have tried to connect Nordic Thingy91 (nRF9160) device using "nRF connect v3.2.0", via USB. But I am facing, below issue.
Issue 1...
Hi,
I am getting the same error despite adding the files properly.I even tried by providing the absolute path.
"nrf_section_iter.h": No such file or directory.
I get errors saying XYZ.h header file is not included though I have included them everywhere. Please help me on how to resolve them.
Regards,
S Sachin Goud
Im use the \nRFready Smart Remote 3 nRF52 v1.2.1alpha\nRF5x SDK-SR3\examples\ble_peripheral\smart_remote_3_nrf52\Projects\Firmware_nRF52832 code ,then I have dowmload the...
Hello -
This is a strange problem and I'm guessing I am missing something obvious. I am using the sd_ble_gap_scan_start() API to perform active scanning as follows:
...
