I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hi everybody,
We are going to develop on nrf52833 our new product. I have some questions regarding this new module:
1- Is the module available to buy online?
2- I saw...
Hello,
We are working on a Tag and Trace type asset monitoring application, that requires scanning several thousand (>6000) beacons in a closed room of about 15feetx15feet...
I am programming and using the monitor mode with Keil seeming ly OK with nrf52-DK dev board however when I program my custom PCB it gives me an error and says the bit cannot...
I designed a reduced size PCB that used an nRF52832 and will act as a BLE HID device.
With the original nRF52DK evaluation board I was able to use the example ble_app_hids_mouse...
Using SEGGER Embedded Studio for ARM Release 3.34a Build 2018022300.35192 Windows x64
with
GCC/BINUTILS: Built using the GNU ARM Embedded Toolchain version 6-2017-q2-update...
Hardware: PCA10040, PPK
SDK: nRF5_SDK_15.3.0_59ac345
I test hrs app and get these number in current consumption during advertising. No modification on example projects...
HI,
We are mainly using "nRFgo Studio" and "nRF Connect" application for erasing and flashing codes to our custom board and its taking place successfully for a long time...
Hi, I am interested in the nRF52811 direction finding capability. In particular, whether its feasible to develop direction findings through a single beacon to receiver configuration...
I am having issues with implementing long-press button action along with normal button press on the same button using the nrf52_sdk_thread on nrf52840.
When I implement...
When mesh_config_clear() is called with a setup containing a file strategy MESH_CONFIG_STRATEGY_ON_POWER_DOWN and an entry in that file has been changed but not yet written...
Hi
I am working on Mesh using light switch example,
1. Wants to relay the ON/OFF message to other server.
2. And send mesh message from server to all node in mesh network...
Hello,
I have program w/o using softdevice to drive an LED driver using I2C. I was able to get this to work very well with out a softdevice, however once I loaded a soft...
Based on nRF5_SDK_15.3.0_59ac345 for nRF52810 application,
a. With s112_nrf52_6.1.1_softdevice.hex and app.hex, it works normally b. Add bootloader, fds_init function will...
On custom nRF51422 hardware with S110, I eventually found that after 3 minutes the advertising timeout turns off the system.
I reproduced it by using the nRF SDK v9 project...
