Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I am trying to configure my nRF9160 v0.8.5 dk for current measurement and found out that SB 44 is missing on my kit. As the user manual suggest that in order to enable...
Dear DevZone team, I am using Thingy91 in NB-IoT mode because I am located in Germany. Last week I managed to connect it to the nRF Cloud by updating the firmware (thingy91_nbiot_legacy_pco_v0...
Hi,
I have multiple sensor data that needs to be recorded in separate files. This data is being collected in parallel. Using the FATFS xample in SDK 15, I am able to write...
Hello all,
I’m trying to connect my nrf51dk (board 1) with a CSR8670 (board 2) using GAIA services and characteristic.
On BOARC 1 i have implemented “Central HRS” beacause...
We made the test with your demo SDK on the board :
PCA10056 1.0.0 2018.46 PCA10056 1.1.0 2019.26
We modify the code to gate the trace ( see the attach file)
And the...
Hello team Nordic,
Example ble_app_rscs_c is working well with my pca10056, im using it to scan for advertising reports. To do the same with pca10059, im trying to merge...
Does the nrf52811 temperature peripheral do automatic linearity compensation? The product specification 1.0 says: " Linearity compensation can be implemented if required by...
I'm currently unable to build the asset_tracker for Thingy:91 on Segger Embedded Studio - using nrf9160_pca20035ns for the nRF Connect SDK Project
Do anyone have an idea...
Dear Team,
what is the way to do it in Zephyr?
I have a signal up-to 10kHz, what is the best way to keep the counter in the background?
Thank you and best
Oleh
In the getting started assistant App
When I run:
pip3 install --user -r zephyr/scripts/requirements.txt
I get this as the error:
However, when I run
pip3 install...
I am doing power consume estimation, need to know detail of RF activities, is there any way to get the total send/recevie bytes of RF? or just simple tx/rx counts? My project...
Based on nRF5_SDK_15.3.0_59ac345 at nRF52810
Bootloader = examples\dfu\secure_bootloader\pca10040e_ble\
Application,
Program Size: Code=36132 RO-data=5176...
This issue concerns code using Softdevice S132 v6.1.1. v5.0.0. I did not test with any other version.
From the documentation of sd_ble_gatts_hvx in ble_gatts.h, I expect...
#define LESC-DEBUG-MODE 0 / set to 1 to use the LESC debu g keys. The debug mode allows you to use a sniffer to inspect traffic. */ The above macro definition is available...
