Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
Hello, I have read posts about programming external boards and want to use BC832 as a beacon. I have been trying to program it with nRF52840 DK and followed these operations...
Hi Devzone!
I'm using uart to send AT commands to LTE modem.
but when I send AT commands the response is quite strange, and I think the command is sent twice. I don...
Hi, I'm using the Zigbee SDKv3.1.0 Cli agent as coordinator, the Zigbee SDKv3.1.0 Ligh_Switch example and two commercial light bulb (Ikea and Heiman) I'm be able to command...
Hi,
TWI init using nrf_drv_twi_init, if event_handler is null it will be blocking mode. My question is, which one is less power consuming? block or non-blocking mode?...
Hi Everyone
*ITS VERY URGENT ISSUE*.
I am using nrf52840 PDK with segger embedded IDE.
I was trying to use the QSPI module to write data to the external flash memory...
Hello All,
I am trying to send data on serial port of nrf9160 to be published on a topic using MQTT protocol. So far using the mqtt example and UART example, I have successfully...
Hi,
We are using nRF52840 DK with PPK stacked on top of it. We flashed BLE power profiling application, connectable advertising and observing graph on PPK.
Please answer...
Hello
I simply wanted to build an executable from a customized nrfutil. Ran the "pyinstaller nrfutil.spec" and afterwards started the nrfutil.exe from command line. This...
Hi , i want to use SDK 16 with BDS template, is there plugin for ? Or its posssibly to use http://developer.nordicsemi.com/nRF51_bluetooth_development_studio_plugin/ with...
Is this a bug that is resolved in a particular softdevice version? If not, is there more information somewhere on this bug? How do i ensure that my code is robust against...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
