I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
I'm using the ble_app_hrs example code and added a new custom services with multiple characteristics . conn.interval 10ms- 15ms and need to get maximum throughput so i set...
I have nRF52840 DK (board PCA10056) . Right now I flashed LED blinking program on nRF52840 DK. It is fine.
Now I want do ADC operation, so I fed some external analog signals...
Hello, I am trying to send and recieve data with the M24C32-FMN6TP 32 Kbit (4K x 8bit) eeprom. My data are arrays with 16bit values and the datasheet says it cannot write...
Hi,
I have nrf9160 dev board.
It seems to me that getaddrinfo() has memory leak. If socket is closed, and call getaddrinfo() to reopen, it returns -10 (memory) error....
i'm looking for support in desinging modules working in zigbee network with driving this network from mobile phone by bluetooth. It has to be multiprotocol system. How should...
Hi,
I was trying to load the sample example code for Assets tracker in SEGGER Embedded Studio for ARM V4.20a but i encountered with some error.
Transcript & Output:- ...
Hi everyone. I've implemented kind of simple FW updater. The purpose is to copy FW from flash (0x0 address, no MBR or SoftDevice) to RAM buffer on node1. than send this FW...
The most recent nRFConnect AppImage version (3.2.0) fails to launch on a Debian system due to chrome-sandbox file permission errors.
Steps to reproduction:
1. In a recent...
I'm using nrf52832 DK and SDK V 15.3 and SoftDevice S132 . I have created a custom services with 5 characteristics. So i want to get maximum throughput so i increased MTU...
Hi
For our semester project, we develop a box that has to reads some parameters from an oil pump system and send data to the cloud. As we wanted to make it independent of...
Hi everyone,
Im looking to put together a security solution consisting of an accelerometer and a proximity beacon. The accelerometer would be installed on gates and authorized...
As part of our evaluation on the Nordic BLE SOC, I want to measure the throughput, range and the power consumption.
Can someone point me to any sample program(s) that I...
A while ago I was experimenting with the usbd_msc demo, trying to get the firmware working as RAM-disk-only storage, without any permanent storage like Flash or SDC. While...
Dear Team,
We need a SoC which can support the following features for our wearable product.
1) Battery Charging
2) I2C interface for sensor
3) GPS
4) BLE
Regards...
Hi, I have run light switch example in SDK 15.2 and SDK for Mesh version 3.1.0, when I try to add new app_onoff_server_t model to Server with my code:
and I have modified...
