I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello
I simply wanted to build an executable from a customized nrfutil. Ran the "pyinstaller nrfutil.spec" and afterwards started the nrfutil.exe from command line. This...
Hi , i want to use SDK 16 with BDS template, is there plugin for ? Or its posssibly to use http://developer.nordicsemi.com/nRF51_bluetooth_development_studio_plugin/ with...
Is this a bug that is resolved in a particular softdevice version? If not, is there more information somewhere on this bug? How do i ensure that my code is robust against...
Are there examples of HW and SW to allow Power Amp, LNA, and TX/RX switch to be connected to the nRF52840_DK?
Or can you tell me what PIN on the chip or connector and pin...
Hello -
We are developing some low power code on the nRF52840-DK, using SDK 15.3.0 on FreeRTOS. I noticed that in the port_cmsys_systick.c file, in the vPortSuppressTicksAndSleep...
I am building a prototype that will use the nrf52840, with limited space. Would making a small pcb antenna or using a chip antenna be better and what is the setup needed for...
Hi,
I would like to measure the voltage generated by a Thermoelectric generator. The voltage vary between -250mV and 250mV depending on the temperature gradient.
If...
I'm looking for alternative xtal's (mhz + rtc) for use on boards where space is very limited.
Silego's GreenCLK3 looks like a great option, though that one is right now...
hi,
I want to use the Bluetooth Low Energy in nRF Connect for desktop. But I have no DK or dongle.
When I use my own development board and the MCU is nRF 52832, it can...
Hi
I am wondering how to choose among different logger mechanisms available in nRF SDK v16.0.
I noticed that some examples doesn't use any logger at all (e.g. blinky...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I have cleared the WDT with "nrf_drv_wdt_channel_feed". I want to make sure it is cleared. Which register can be used to confirm...
Hi I am using Keil ARM with JLINK to debug the NRF52832. I can download the flash on the PCBA but when I try to debug step-by step, it only runs on the assembly window but...
Hello ...
Implementing an app for both nRF51822 and nRF52810 and need a long-term clock with 100 Hz counter frequency to timestamp sensor events. By long-term, I mean at...
HI,
I've been looking at the nRF52811 registers for AoA/AoD, and decided to try and at least get CTE enabled on the basic Nordic uart app. I found this post:
https://devzone...
Hello. In acrording to:
How the bridge exchange information between mesh network and mobile device
The bridge using Nordic UART Service to conduct the command/response...
