Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
I receive this output from west when trying to build the asset_tracker example from either master or v1.1-branch:
west build -b nrf9160_pca20035ns -- west build: build configuration...
Hi
I am using a buttonless DFU to do OTA for my application. Everything is working fine up to now, but now my custom board got few modifications of using PIN 16 for USB...
I am trying to complie Eddystone project which is part of NRF5 SDK and when i compile the project in Embedded Studio I get the following error
/resized-image/__size/738x210...
Hello. I am developing with the following configuration.
In this configuration, since it is necessary to connect multiple peripherals with multiple roles, "scan_start...
Since migrating to the Zigbee 3.1 SDK I have noticed a few oddities with the behavior of attribute reporting that I am thinking are related to the following bugfix:
The...
HI,
I find that the DFU code start address regsiter is different between SDK15.3 and SDK16
SDK15.3
MemorySegment name="uicr_bootloader_start_address" start="0x00000FF8...
Hi,
I'm using the Home Automation profile of the Zigbee protocol and, in particular, I'm developing the Window Covering Device, present in the SDK "nRF5_SDK_for_Thread_and_Zigbee_v3...
It appears the softdevice gets into a strange state when a BLE connection is lost while transferring data. How does application code reset or reinitialize the softdevice ...
Hello,
On the documentation page for nRF5 SDK for Mesh ( https://www.nordicsemi.com/Software-and-tools/Software/nRF5-SDK-for-Mesh ) it says that only the nRF52832 and nRF52840...
Hello,
I'm seeking some clarification on a few points to determine the performance of the nRF52840 in high density deployments. The current intended soft device is S140...
Hello,
in the current project we use a large array (16kB) in RAM to store data. After a reset we would like to check if the array is not corrupted to continue processing...
Dears,
I'm using nrf52832 with PCA10040 and SDK 16.0.0,I want to make a DFU via uart. So used the firmware provided in the SDK(nRF5_SDK_16.0.0_98a08e2\examples\dfu\secure_dfu_test_images...
Hello,
I would like to evaluate nRF9160 for incoming project.
I have Nordic Thingy:91 with iBasis sim card.
Unfortunately, during configuration it turned out, that...
Hi,
We are using nRF9160 for our application and need to design power supply with battery management IC for it and need to know how much power it will consume with all...
